(c) The block diagram of a fluidic speed control system is shown in Fig. 1 where the actual speed C(s) is system output and R(s) is reference speed. Show that the closed-loop transfer function is given by Reference Speed R(s) C(s) R(s) K 100s²+s+Ka Amplifier Valve actuator Turbine Actual Speed 1 + Ка S 1+100s C(s) Figure 1

(c) The block diagram of a fluidic speed control system is shown in Fig. 1 where the actual speed C(s) is system output and R(s) is reference speed. Show that the closed-loop transfer function is given by Reference Speed R(s) C(s) R(s) K 100s²+s+Ka Amplifier Valve actuator Turbine Actual Speed 1 + Ка S 1+100s C(s) Figure 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are static error coefficients? how will you calculate the steady state error using static error coefficients? (Write equations also, about kp, Kv, Ka) subject: control system
Two masses are connected by sprchgs as shown in the accompanycng diagram. Bolh sprchgs constant, and the end ö have the same spochg f is bixed. 16 x, and X, represent the equilibreum position, derive a system of second - order that describes the birst spreing the displace ments brom dibterential motion equations of the system. the
We added the shown Pl controller to reduce the steady-state error of this system to become ess=0.5 for a unit ramp input. Determine K, that allows us to do that. Hint: start by finding the static velocity constant Kv. R(s) Answer: K₁ 19 +- S controller 1 5s + 1 plant C(s)
Consider the given system with input R(s) and output C(s) as shown in figure. • Calculate the natural frequency of oscillations, damping ratio, peak time, rise time, settling time, percentage overshoot and damped frequency of oscillations. • Also find the (time domain) expression for unit step response and Plot. Note: x=3
For the control system, shown in the following figure, determine the steady-state error for a unit step input in terms of K and K,, where E(s) = R(s) – C(s). Determine the value of K, when steady-state error is zero: E(s) R(s)- C(s) s(s+ 10) (s+ 12)
Task 2: Consider the electrical system in the figure below, derive a differential equation that expresses the relation between the rate of change in the capacitor voltage Vc, and the voltage across the resistor VR. (Hint: use Kirchhoff current law). (i) (ii) (iii) СЕ Formulate a first order differential equation to express the previous system. Hint: use Kirchhoff current law. Find the general solution of this first order differential equation, Assume: C-50 Micro Farad and R=50 ohm. Show how this differential equation could also be solved using Laplace transform to determine the particular solution. Table of Laplace transforms A to 4 T 12 sin kr cask! k 446 Fis) = Lif(t)) (+4)² a 320 15-A $5-A R 12.0 y>0 ²+²>0 L{f'(r)] = $F(s)-f(0) Lif"(t)) = s²F(s) - sf (0) - f'(0)
Can you explain each step clearly to solve this? I will rate, thank you!
A motor. whose torque speed curve is Tm= -0.5wm+ 50 when the input voltage la 10 V, drives the load shown in the diagram in Figure 1. Find the transfer function, . If the following values are given as J1 = 3 kg-m2 , J2 =7 Kg-m2, D = 2 N-m- s/rad, N1 = 40, N2 = 10. %3D %3D given as J=3 kg-m", J= T Kgem Om Ca(t) Motor N2
The effective life of a component used in a jet-turbine aircraft engine is a random variable with mean 5000 hours and standard deviation 40 hours. The distribution of effective life is fairly close to a normal component that increases the mean life to 5030 hours and decreases the standard deviation to 30 hours. distribution. The engine manufacturer introduces an improvement into the manufacturing process for this Suppose that a random sample of n₁ = 16 components is selected from the "Old" process and a random sample of n₂ = 25 components is selected from the "Improved" process. What is the probability that difference in the two-sample means that the old and improved processes can be regarded as independent populations. - X₂X₁ is at least 15 hours? Assume
A closed-loop control system is created using a proportional controller. Show that such a system has a steady state error of 1/(1+Kp) and therefore the steady state error condition can be achieved with a proportional gain of 9 or more.
Q4) A particular control system yielded a steady state error of 0.20 for unit step input. A unit integrator is cascaded to this system and unit ramp input is applied to this modified system. What is the value of steady-state error for this modified system? 05) Eer the ontrol ouoton lou
Electrical Engineering please can you explain with proper steps how the author came up with the answer to this question. i am trying very hard but i cannot seem to get an answer to this question 2. A synchronous generator is delivering 30 % of the maximum power to an infinite bus. If the mechanical input is suddenly increased by 100%, will the synchronism be lost? If not, what is the maximum excursion of ổ about the new steady state? (Ans:58°)