(c) Design a voltage regulator using the circuit in Figure 3. The voltage regulator is to power a car radio at V = 9 V from an automobile battery whose voltage may vary between 11 and 13.6 V. The current in the radio will vary between 0 (off ) to 100 mA (full volume). Iz(min)=0.1 Iz(max). Hint: Find the suitable current limiting resistor and Zener diode. %3D R; Vps Radio Figure 3. Circuit for design

(c) Design a voltage regulator using the circuit in Figure 3. The voltage regulator is to power a car radio at V = 9 V from an automobile battery whose voltage may vary between 11 and 13.6 V. The current in the radio will vary between 0 (off ) to 100 mA (full volume). Iz(min)=0.1 Iz(max). Hint: Find the suitable current limiting resistor and Zener diode. %3D R; Vps Radio Figure 3. Circuit for design

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
In the circuit shown in the figure; B) When RL = 1Kohm and capacitor C is deactivated, draw VA and V0 in scale according to input voltage Vs. NOTE = diodes are ideal
In the circuit shown in the figure; A) When RL = 5Kohm and capacitor C is switched on, draw VA and V0 in scale according to input voltage Vs. NOTE = diodes are ideal
How do I calculate the dynamic resistance of a zener diode with the following set of values given please? The circuit in figure is the circuit in question I am trying to solve this for please. Vin(DC) = 10V vin(ac) = 0.05sin(wt) Vz(voltage of diode) = 4.5V R1 = 1000 ohms
The voltage signal coming out of the capacitor is with small ripples compare to the voltage signal out of the diode. True False
uO 9:.0 A docs.google.com * ZAIN IQ l. Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 9kQ 1N1199C R2 D1 18KQ 1N1199C D3 1N1199C V2 =12 V R3 1kQ R4 5kQ 1.22 V 11 mA 0.5 A O VD1 ID1 VD2 ID2 صفحة 4 من 6
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A zener diode exhibits a certain change in VZ for a certain change in IZ on a portion of the linear characteristic curve between IZK and IZM as illustrated in Figure 5. Calculate the zener impedance.