An electric motor running at 600 rpm is used to drive a rock crushing machine with a design power of 28 kW. A 32 oz ducking weight flat belt drive is proposed with a tension ratio of R = 3 and belt width b = 125 mm. The pitch diameter of the driving pulley (on the motor-end) is 300 mm. a) What is the mass per mm width per m length per ply in kg/mm/m/ply? Number (exact value) b) What is the maximum working tension per mm width per ply in N/mm/ply? Number (exact value) c) Calculate the belt velocity in m/s Number (+/-1%, d) Determine the number of belt plies required. Your answer should be an integer number (no decimals). Number (exact value)

An electric motor running at 600 rpm is used to drive a rock crushing machine with a design power of 28 kW. A 32 oz ducking weight flat belt drive is proposed with a tension ratio of R = 3 and belt width b = 125 mm. The pitch diameter of the driving pulley (on the motor-end) is 300 mm. a) What is the mass per mm width per m length per ply in kg/mm/m/ply? Number (exact value) b) What is the maximum working tension per mm width per ply in N/mm/ply? Number (exact value) c) Calculate the belt velocity in m/s Number (+/-1%, d) Determine the number of belt plies required. Your answer should be an integer number (no decimals). Number (exact value)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a distance of 12 m from the driving pulley of 480 cm diameter ?
Problem 4. For the belt drive shown below calculate the contact angle 0, if: D %3D 100 mт; d 3 30 тm; C = 300 mm. D-d 20 sin V4c² - (D – d)²- -1 D-d sin 20 Op
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
(Q2) A pump is driven by an electric motor using an open type flat belt. Determine the width and length of belt for the following data: Power transmission = 15kW Rotational speed of the motor=1,440 rpm Motor pulley diameter = 250 mm Pump pulley diameter = 500 mm Coefficient of friction for motor pulley = 0.26 Coefficient of friction for pump pulley 0.22 Center distance between the pulleys = 1,200 mm Thickness of the belt = 5 mm Density of belt material = 1,000 kg/m? Allowable stress for the belt material = 2 MPa
The following figure shows a cable lifting system, the lifting system is derived by an electric motor through a V-belt and spur gear that is coupled with the drum. Replace the V-belt drive with one step of helical gears if the input power is 40hp. Specify the design whether is satisfactory or not. Electrical motor n, 870 r.p.m- small sheave speed v-belt Drum radius = 40 cm Pinion Gear non, 200 r.p.m pinion and biggest sheave speed ne=100 r.p.m cable Crate weight = 800 kg
A belt drive operates with sheave sizes of 5.25 in and 13.95 in. If the center distance (C) is specified at 24 in, what is the theoretical belt length required? (A) 61.35 in (B) 70.25 in 78.93 in (C) (D) (E) 84.12 in 89.02 in
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
0 1.6m B) G+ Motor 75 mm 75 mm 150mm 1.4 m Figure 5 Fixed support (b) The diameters of shaft AB and CD in Figure 5 are 50 mm and 75 mm, respectively. The length AB is 1.6 m and the length CD is 1.4 m. Gear at B has a radius of 75 mm and gear at C has a radius of 150 mm. The motor produces 180 kW power at a frequency of 30 Hz. Given the shear modulus of elasticity of the material is 77 GPa D If the shafts are solid shafts, determine the shearing stress in the solid shafts and the angle of twist between A and D. If the shafts are hollow shafts, determine the thickness of each shaft so that the allowable shearing stress of 55 MPa and the allowable angle of twist of 2.5° for each shaft are not exceeded.
Two shafts 30 in. apart, each carrying a four-step pulley, are to be connected by a cross belt. The driving shaft is to turn 180 rpm while the driven shaft is to turn 50, 150, 250, and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find (a) the diameters of all the steps, (b) angle of contact for each pair of pulleys, and (c) belt length.
Q2 Select a suitable chain drive to transmit 50 kW from an electric motor to a line shaft. The motor shaft r.p.m. are 1200, line shaft r.p.m. are 250 and approximate center distance is 600 mm. Assume service is 10hr/day, 6 days per week.
2. A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys. [Ans. 35.9 kW]
A cross belt drive has a 6 in. pulley driving a 48 in. pulley. The distance between their centers is 96 in. Find the length of the belt needed. Please Show a clear and detailed solution (with illustration). Thank you!