Answered: An earth embankment is shown in the…

An earth embankment is shown in the figure. Determine the stress increase at 2. point A due to the embankment load, 7 m 15 m Unit Weight 19 kN/m' %3D 8 m 10 points 2. Increase in stress

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.13P: Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below...

See similar textbooks

Related questions

Q: 3. An earth embankment is shown in Figure 3.48. Determine the stress increase at point B due to the…

Q: An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 (from…

A: Given Data: c=25 kPa Angle of internal friction=260 Weight of fill per unit volume=18.64 kN/m3…

Q: 15 m C IN 2 3.5 m 3.5 m BA 2 Unit weight y = 19 kN/m³ 8 m ↓

Q: If the gauge of the railroad shown on the plan above is 1.7 m and produces a line-like loading at…

Q: 7. For the soil profile shown below, plot the variation of total stress, effective stress and pore…

A: Total stress in soil is load per unit area at any given plane in soil mass is either due to self…

Q: Given the soil element, determine the following: a. Maximum and minimum principal stresses b. Normal…

Q: Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit…

A: Draw the figure.

Q: An embankment shown in the figure is constructed. Compute and plot the distributions of the vertical…

Q: If the gauge of the railroad shown on the plan above is 1.7 m and produces a line-like loading at…

A: Data given;Gauge of railroad= 1.7mdistance (Y) = 1.9mDepth = 0.5mFormula used:I=1π(2×θ+sin2θ)

Q: A rectangular foundation of 4m x 6m (as shown in Figure 4) transmits a stress of 150 kPa on the…

A: given stress σ=150kPa

Q: Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit…

A: Given data Unit weight Depth Dimensions To find Stress at point A

Q: A rectangular foundation 4 m × 6 m (Figure P7.20) trans- mits a stress of 100 kPa on the surface of…

A: We have to find the value of depth at which the increase in vertical stress below A less than 10% of…

Q: Problem (4.9): An embankment of (3m) high is to be constructed as shown in the figure below. If the…

A: Solution: Considering the Diagram 1. Vertical Stress at A: By considering the FigureσzA=σz1+σz2Left…

Q: The soil in a deposit underlying an area where a level ground surface exists has a unit weight of 22…

A: Given: Unit Weight of soil = 22 kN/m3, Depth = 5m

Q: An embankment shown in the figure is constructed compute the vertical stress increment under Points…

A: load, q = γt H = 19.2×6 = 115.2 KN/m2 a) At Point A, centre , stress is calculated by superposition…

Q: Q.4) Determine and plot the variations of total and vertical stresses and pore water pressure with…

A: Given data Unit weights Depths Water table and its depth Formula to be used Effective stress =…

Q: The soil stress state is shown in the figure, σx = 10 kN/m2, σy = 50 kN/m2, τxy = -10 kN/m2 What is…

A: The angle of intersection is given by:

Q: 7. For the soil profile shown below, plot the variation of total stress, effective stress and pore…

A: Effective stress: The term effective stress is defined as the total stress minus pore water…

Q: Plot the variation in the effective stress (o') for the given soil profile. Plot your answer here…

Q: Question 2/ The soil profile shown in Figure (2) subjected to downward seepage calculate the…

A: Soil subdivision can be done in many ways and there are many types of soils such as clay, dust, etc.…

Q: Another method of determining the capillary rise in a soil is to use Hazen's capillary formula. The…

Q: SITUATION. From the soil profile shown below, Ground surface Dry Sand Clay A e = 0.49 Gs=2.68 Ground…

Q: A highway embankment is shown in the figure below. If the unit weight of the soil in the embankment…

A: Given: The unit weight of the soil is 17.5 kN/m3. Consider the figure,

Q: 8.10 An embankment shown in the figure is constructed. Compute and plot the distributions of the…

A: Given data z=10 m γt= 19.2 KN/m3

Q: Question attached

A: Given data- Effective dia Do =0.01 mm = 0.001 cm

Q: 3 m 1 m A seepage flow condition is shown in the figure. The saturated unit weight of the soil Yar…

Q: 35 At the construction site, 3 m thick clay layer is followed by 4 m thick gravel layer which rest…

Q: (Use The Figure (10.20) to find the solution of this question) An embankment load on a silty clay…

A: We need to measure the stress increase beneath the embankment at sites A and B, which are located at…

Q: The sand layer shown is subjected to a downward flow of water. (52.58, 0.436, 14.36) In flow 0.70 Z…

Q: An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 9from…

Q: An embankment is being built of a soil whose unit weight is equal to 18 kN/m³. The pore pressure…

A: given values- Pore pressure parameters-A=0.6B=0.8change in height 6 m to 9 m

Q: Problem1) According to the given soil profile, fill the table and plot the distribution of vertical…

Q: Problem 2: A soil element is shown 5.4 kN/m2 in the figure on the right. The magnitude of stresses…

A: Answer:- It can solve by the help of formula for major and minor principal stresses.…

Q: A soil profile consists of a clay layer underlain by a sand layer, as shown in the figure. If a tube…

Q: 6. From the given soil profile, the groundwater table is located 2m below the ground level. (See…

Q: 8.10 An embankment shown in the figure is constructed. Compute and plot the distributions of the…

Q: Problem No. 1 An earth embankment diagram is shown in Figure. Determine the stress increase at point…

A: I try to give detail and neat explanation for this question, so if possible give me a feed back plz?…

Q: An earth embankment is shown in Figure 3.4. Determine the stress increase at t A due to the…

Q: 10.15 For the embankment shown in Figure 10.45, determine the vertical stress increases at points A,…

A: - Total load of embankment per meter length is, Length of base = 10+(22.5*2.25*2)=111.25 m Q=Unit…

Q: The soil profile at a site of a 10 m thick sand layer is shown in the figure below. The total active…

Q: An embankment shown in the figure is constructed. Compute and plot the distributions of the vertical…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Question 1: You are designing a retaining wall at the construction site. The friction angle of sand…

Q: (c) Figure 3.2 shows the general arrangement for a total stress analysis of a clay slope. Prove from…

Q: Q.01 0.02 0.04 0 06 0.10 0.2 0.50 L 04 0.6 1.0 2 3456 8100 0.60 12.0 m 18.0m 19.0m 045 0.45 6.0 m 0…

A: Solution:- We know that the equation obtained by Boussinesq for computing vertical stress for…

Q: Calculate the geostatic stress at point A, the soil unit wieght is 18 kN/m3. 6 m 1.6 m 3 m PLAN 1.5…

A: Option C is the correct option. GeoStatic Stress- These are stresses caused by the soil itself. Soil…

Q: An earth embankment is shown in the figure. Determine the stress increase at point B due to the…

A: Consider the given diagram.

Q: An earth embankment is shown in Figure 10.44. Determine the stress increase at point A due to the…

A: In hydraulic engineering and flood control, embankments are used to hold water back and for flood…

Q: onsider the soil profile shown in Figure 1.4: How high should the groundwater table rise/drop so…

A: calculate effective stress at c so calculate dry unit weight of dry sand…

Q: A soil profile consists of a clay layer underlain by a sand layer, as shown. If a tube is inserted…

A: To Find Effective stress and Pore water pressure at point A,B & C.

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

An earth embankment is shown in the figure. Determine the stress increase at
2.
point A due to the embankment load.
7 m
15 m
Unit Weight 19 kN/m'
%3D
8m
10 points
2. Increase in stress

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2: An embankment shown in the figure is constructed. compute the vertical stress increment under Points A. B. and C at z = 10 m Use vertical stress Increment under an embankment loads? 10 m 12 m 10 m Y₁-192 kN/m² Take value of 15 from chart s6v=9[s
With B,lz and Blz is showr CE 12 s Name: ID: Problem No. 1 For the embankment shown in Figure below, determine the vertical stress increases at points 4, B, and C. 5m 5 m 10 m Unit weight y 17Na 5 m
An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface. 5 m 1H:2V 1H:2V 1H:1V 8 m 13 y=18 kN/m Y=18 kN/m³ 6 m : B : A CS Scanned with CamScanner
Take o, = 580 kPa (Figure 1) Express your answer to three significant figures and include the appropriate units. HÀ ? o, = Value Units Submit Request Answer Figure Part B Determine the shear stress acting on the inclined plane AB. Express your answer to three significant figures and include the appropriate units. В HA ? 30° Value Units A
Estimate and plot the vertical stress increase, Aoz, along verticals through A, B, the centerline, C and D of the embankment at depths of 0 ft, 10 ft, 20 ft, 30 ft, 40 ft and 50 ft below the original ground surface. Plot also the variation of Aoz along horizontal planes at similar depths. Assume y = 120 pcf. 25ft A * B £ * с D 15ft TEIN
Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit weight of the embankment fill is 115pcf
Stresses in Soil Mass: Mohr's Circle 131.6 kPa 53.6 kPa 315.2 kPa 315.2 kPa 35 131.6 kPa 2. Find Normal and Shear Stress at Failure Plan A-B. Enter your answer to three significant figures. (1 decimal place)
Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit weight of the embankment fill is 115 pcf. 20' 20' 40' 20' 25' 30' A
The soil profile at a road construction site is as shown in figure (not to scale). A large embankment is to be constructed at the site. The ground water table (GWT) is located at the surface of the clay layers, and the capillary rise in the sandy soil is negligible. The effective stress at the middle of the clay layer after the application of the embankment loading is 180 kN/m². Take unit weight of water, Yw = 9.81 kN/m3. Embankment load boudi Sand GWT 2m y = 18.5 kN° it enit Clay Specific gravity, G̟ = 2.65 Water content, w = 45% Compession index, C. = 0.25 6m %3D %3D Impermeable layer The primary consolidation settlement (in m, round off to two decimal places) of the clay layer resulting from this loading will be
Q#3. An earth embankment diagram is shown in Figure.1. Determine the vertical stress increase at A due to embankment load.
7. 4) Determine the increase in vertical stress at a depth (2) m belowpoint A due to surface loads shown in Figure (2). m or n L.O 10.0 9.0 8.0 7.0 6.0 5.0 4.0 E 3.0 2.5 2.0 G.S.L xxxx 1.5 z 1.5 -0.006- -0.007 0.006 0.009 0.15 19 -0.011 0.010 Section b-b 2 160 kPa 0.2 0.012 0.014 m or n 2.5 3 G014 0.016 0.020 & 0.25 0.3 0,024 120 kPa 4 2.000 0.4 5 -0.04 6 0.06 S b + 7 8 9 10 0.13 ats 0.34 0.5 0.6 0.7 0.8 0.9 1.0 m or n (a) 2.5 m 160 kPa 120 kPa ais. 1.5 . 1.5 2 2.5 3 2.5 T 3 1.5 m 2 m 0.5 m 4 4 5 Fig.(2) 6 7 8 9 . 1 10 11.0 0.9 0.8 0.7 0.6 40.5 10.4 0.3 0.25 0.2 m of n E 0.15 0.10 .9 10
Ql- An embankment is to be constructed over a layer of soft clay 16 m thick as shown in figure 1. Construction the embankment will increase the total vertical stress in the clay layer by 110 kPa. The design requirement is that all but 25 mm of the settlement due to consolidation of the clay layer will have taken place after 6 months. Determine: A. The spacing in best pattern of 500 mm diameter sand drains to achieve the above requirement. B. Which is the best, the use of sand drains or pre-fabricated drains? Why? (25%) Embankment Clay Cy = 4.7 m2/ year Ch = 7.9 m2/ year mv= 0.25 m2/ MN 16 m Sand Figure (1).