After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of water. What is the maximum permissible value of d so that the water level will just barely reach the brim of the glass, as shown? Assume that the SG of the glass is 2.55. i/cin-||+-2 in- 4 in. I SAE oll Water

After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of water. What is the maximum permissible value of d so that the water level will just barely reach the brim of the glass, as shown? Assume that the SG of the glass is 2.55. i/cin-||+-2 in- 4 in. I SAE oll Water

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter3: The Structure Of Real Materials

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has a velocity of 0.6x103 m/s. If the surface area of the plate in contact with the liquid is 0.6 m?, determine the approximate viscosity of the liquid. B B B' 3 mN 4 mm A
1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has a velocity of 0.6x103 m/s. If the surface area of the plate in contact with the liquid is 0.6 m2, determine the approximate viscosity of the liquid. В в B B' 3 mN 4 mm A
d) Calculate total hardness in ppm of a solution of both 55 mg/L Al2(SO4)3 and 45 mg/L Mg(NO3)2.
The minimum safe bending radius of a certain polyethylene tube is theoutside diameter times 31⁄2. The tube has an outside diameter of 3⁄8 inch.What is the minimum bending radius?
A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is shown. At an initial temperature of Ti = 22°C, the outer diameter of the disk is D = 210 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 24 mm. At a final temperature of Tf = 46°C, determine:(a) the change in diameter Δd of the central hole (assume an increase Δd as positive, otherwise as negative).(b) the change in thickness Δt of the disk (assume an increase Δt as positive, otherwise as negative).(c) the normal strain in the circumferential direction around the outside of the disk.
A circular nylon [E = 8 GPa; v=0.35; a=20x106/°C] disk with a circular hole in its center is shown. At an initial temperature of T;= 19°C, the outer diameter of the disk is D = 230 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 19 mm. At a final temperature of Tf= 52°C, determine: (a) the change in diameter Ad of the central hole (assume an increase Ad as positive, otherwise as negative). (b) the change in thickness At of the disk (assume an increase At as positive, otherwise as negative). (c) the normal strain in the circumferential direction around the outside of the disk. O Answers: (a) Ad= (b) At= (c) Ecirc 0.0363 0.01254 660 D mm mm με
A commercial screen cloth of market grade is used to separate different fractions of 300 m³/hr of crystals obtained from crystallization via nucleation process in a cylindrical vessel of 3 m height and 9.25 m OD of thickness 3.6 cm. The properties of the slurry are: M, = 220 g/L; p = 1.26 g/mL; P = k, = 0.97 Mesh Sizes wt % -7 mesh +9 mesh 1.68 -9 mesh +12 mesh 2.31 -12 mesh +14 mesh 2.12 -14 mesh +18 mesh 13.90 -18 mesh +24 mesh 32.89 -24 mesh +40 mesh 45.78 -40 mesh Find: Kinetic equation b. Dominant particle c. What is the cumulative weight fraction at 700 microns? а.
A 13 in length of aluminum tubing (with E = 11.4 x 106 psi and  = 12 x 10-6 /deg F) having a cross-sectional area of 1.6 in2 is installed with “fixed” ends so that it is stress-free at 70 deg F. In operation, the tube is heated throughout to a uniform 500 deg F. Careful measurement at the higher temperature indicates that the fixed ends separate to 13.008 in. What loads are exerted on the ends of the tube, and what are the resultant stresses?
A rectangular nylon [E = 8 GPa; ?= 0.35; ? = 24 ×10 6/°C] plate has a circular hole in its center. At an initial temperature of T¡ = 15°C, the plate width is b = 260 mm, the plate height is h = 160 mm, the diameter of the central hole is d = 45 mm, and the thickness of the plate is t = 17 mm. At a final temperature of Tf= 52°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate. b h
The absolute viscosity of the liquid is 1.8 x 10^-3 Pa-s and its SG is 2.00. Compute the equivalent value in stokes
A capillary tube of diameter 2 mm is placed in a reservoir of water, and a similar capillary tube is placed in a reservoir of methanol. If both tubes are made of clean glass and the water-glass and methanol-glass contact angles are both approximately equal to 0°. Surface tension of water is 0.073 N/m. Surface tension and density of methanol are 0.0225 N/m and 791 kg/m3, respectively. 8.0 Determine the rise of methanol. a.) 7.4 mm b.) 5.8 mm c.) 14.9 mm d.) 2.9 mm e.) 9.0 Determine the rise of water. a.) 7.4 mm b.) 5.8 mm c.) 14.9 mm d.) 2.9 mm e.).
A commercial screen cloth of market grade is used to separate different fractions of 300 m3/hr of crystals obtained from crystallization via nucleation process in a cylindrical vessel of 3 m height and 9.25 m OD of thickness 3.6 cm. The properties of the slurry are: MT = 220 g/L; ρ = 1.26 g/mL; φ = kv = 0.97 Mesh Sizes wt % -7 mesh +9 mesh 1.68 -9 mesh +12 mesh 2.31 -12 mesh +14 mesh 2.12 -14 mesh +18 mesh 13.90 -18 mesh +24 mesh 32.89 -24 mesh +40 mesh 45.78 -40 mesh Find:a. Kinetic equationb. Dominant particlec. What is the cumulative weight fraction at 700 microns?