A38 A uniform beam AB of length 5 m and which weighs 200 N is supported horizontally by two vertical ropes X and Y at A and B respectively. Calculate the tensions in the ropes if a man weighing 700 N stands on the beam at a distance of 2 m from A.

A38 A uniform beam AB of length 5 m and which weighs 200 N is supported horizontally by two vertical ropes X and Y at A and B respectively. Calculate the tensions in the ropes if a man weighing 700 N stands on the beam at a distance of 2 m from A.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 32P

See similar textbooks

Related questions

Q: A uniform 30 lb beam 10 ft long is carried by two men A and B, one at each end of the beam. a. If a…

A: The torque acting on an object is defined as the product of the perpendicular force acting on the…

Q: How much compression acts on the hip during two-legged standing, given that the joint supports 250 N…

A: Looking at the components Rcosα=Fmcos70=600cos70Rsinα=mg+Fmsin70=250+600sin70

Q: A non-uniform rod of length 1.00 m is hung horizontally, supported by strings on both ends. If the…

Q: The figure shows three boards clamped together. The center board weighs 93.5 N, and the coefficient…

A: The figure shows the force acting on the three boards clamped together.

Q: A sculptor has hung up a 45.0 kg horizontal rod of length 4.85 m . One end of the rod is supported…

A: Given,

Q: A uniform plank of length 2.00 m and mass 31.0 kg is supported by three ropes, as indicated by the…

A: Given, Mass of the plank (m) = 31.0 kg Weight of the person (W)=680 N d=0.500 m

Q: A uniform board is suspended from a ceiling and supported horizontally by two wires, A and B. The…

A: Draw the free body diagram

Q: The board sandwiched between two other boards in Figure P4.77 weighs 95.5 N. If the coefficient of…

Q: A2 m long horizontal uniform beam of mass 16 kg is supported by a wire as shown in the figure. The…

A: Given, Length of beam l = 2 m Mass of beam is mbeam = 16 Kg Angle θ=29∘ Distance where mass attach x…

Q: . The figure represents the concurrent force system acting at a joint of a bridge truss. Determine…

A: For equilibrium of system net force acting on the system must be zero and horizontal as well as…

Q: A 2"x4" of length 2.0 m and mass 5.0 kg is supported by two saw horses which are 1.0 m high, one at…

A: Given Information: The mass of the rod (m) = 5 kg The length of the rod (l) = 2 m The height of the…

Q: A uniform drawbridge must be held at a 38.5 ∘∘ angle above the horizontal to allow ships to pass…

A: Given data-

Q: For the beam and loading shown, determine the tension in cable BC if P = 165.8, Q = 249.3, R =…

A: Here, a figure is given. Also, it is given that, P = 165.8, Q = 249.3, R = 355.4, S = 268.2, T =…

Q: A uniform awning of mass 30 kg is attached to a building at one end and supported by a massless…

Q: A non-uniform rod of length 1.00 m is hung horizontally, supported by strings on both ends. If the…

A: Length of the rod is L = 1 m The centre of gravity of the rod is x = 0.200 m

Q: 3. The members of a truss are pin-connected at joint O. Determine the magnitudes of F1 and F2 for…

A: Solution:

Q: A uniform ladder of length L and weight w is leaning against avertical wall. The coefficient of…

A: From figure at equilibrium we have

Q: a rod of mass m is hinged to a building at its lower end, while its upper end is held in place by a…

Q: A uniform beam is 4.38 m long and has a mass of 69.1 kg. In the figure, the beam is supported in a…

Q: 7. A uniform ladder of mass (m = 15.0 kg) and length (L) leans against a frictionless wall, see…

A: Draw the diagram.

Q: Look at the figure below. The horizontal beam weighs 200N, Find the tension in the cable if the…

Q: The two structural members, one of which is in tension and the other in compression, exert the…

Q: A 1 200-N uniform boom atϕ = 65° to the horizontal is supportedby a cable at an angle θ =25.0° to…

Q: A uniform ladder of length L, rests against a smooth, vertical wall. If the mass of the ladder is m…

A: Draw the free body diagram for the ladder

Q: The two structural members, one of which is in ten- sion and the other in compression, exert the…

A: Given: The compression in the member is 3 kN. The tension in the member is 2 kN. The free-body…

Q: 10. A uniform ladder of mass (m = 11.0 kg) and length (L) leans against a frictionless wall, see…

A: The free body diagram is depicted below,

Q: 1(0 End A of horizontal slender rod AB presses against a rough vertical wall because it is supported…

A: The free body diagram for the loading system given can be drawn as below in the figure: From the…

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A: Balance torque about point O would give us the value of P required to lift the cart from point B

Q: A taho vendor carries a 1.5 m long light plank over his shoulder. At the ends of the plank are two…

A: Analyze the diagram of the given situation. Here, F and x represent the force exerted by his…

Q: A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A…

Q: A diving board 3.00 m long is supported at a point 1.00 m fromthe end, and a diver weighing 500 N…

Q: A 7-m long beam of negligible mass is hanged horizontally and is supported at each end by vertical…

Q: A bar A8 of lengıh (0,6 m and weight 3 N is Suspended horizontally by two strings at A and B. Given…

A: Given, Legth (L) = 0.6 m Weight (W) = 3N

Q: In the figure, one end of a uniform beam of weight 440 N is hinged to a wall; the other end is…

Q: Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope…

A: Hi, your question has multiple sub-parts so we will solve three sub-parts for you. for remaining…

Q: 10. An object weighing 225 N is supported by a uniform 120 N horizontal beam as shown in the figure.…

Q: a horizontal rod (m=5.2 kg) is hinged to a wall at the left end and three forces are acting on the…

Q: A uniform 0.40 kN boom is supported as shown. Find the tension in the tie rope and the components of…

Q: A uniform ladder of mass (m = 13.5 kg) and length (L) leans against a frictionless wall. If the…

Q: А B 45.##° 30.##°

A: For equilibrium net force acting on the system must be zero and horizontal and vertical forces must…

Q: a uniferim rod AB is weighs SN. what is necessary to produced equilibrium c from A) ? Cand 5N A I 20…

A: Given: We need to find force F at distance x cm from point A to keep this rod in equilibrium.

Q: The two structural members, one of which is in ten- sion and the other in compression, exert the…

A: In this problem, forces are divided into x and y -direction and than find resultant force and it's…

Q: A uniform 37.0 kg scaffold of length 6.2 m is supported by two light cables, as shown below. An 82.0…

Q: Neglecting the weight of the bracket, and if s = 6.4 cm, S1 the horizontal force component exerted…

Q: The two structural members, one of which is in tension and the other in compression, exert the…

A: We have two forces F1=4.2 kN which makes an angle of 63o with the +x axis directed inwards and…

Q: The horizontal beam weighs 150 and its center of gravity is its center. Find the tension in the…

A: Given: The weight of the horizontal beam is 150 N. The weight of the load is 300 N. The free-body…

Q: A uniform drawbridge must be held at a 36.5 angle above the horizontal to allow ships to pass…

Concept explainers

Estimate of calculation

Question

Show all working explaining detailly each step.

A38 A uniform beam AB of length 5 m and which
weighs 200 N is supported horizontally by two
vertical ropes X and Y at A and B respectively.
Calculate the tensions in the ropes if a man
weighing 700 N stands on the beam at a
distance of 2 m from A.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
Find the magnitude of the tension in each supporting cable shown below. In each case, the weight of the suspended body is 100.0 N and the masses of the cables are negligible.
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
A suspender rod of a suspension bridge is 25.0 m long. If the rod is made of steel, what must its diameter be so that it does not stretch more than 1.0 cm when a 2.5104kg tuck passes by it? Assume that the rod supports all of the weight of the truck.
A 5.45-N beam of uniform density is 1.60 m long. The beam is supported at an angle of 35.0 by a cable attached to one end. There is a pin through the other end of the beam (Fig. P14.30). Use the values given in the figure to find the tension in the cable. FIGURE P14.30
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
A large advertisement board (W) is held in position by cable F1 , with a breaking strength of 1500 N and a wooden strut F2 with a breaking strength of 750 N. Calculate the maximum weight on the board can hold.
A UNIFORM ROD OF LENGTH 3M AND WEIGHT 100N, WITH ENDS A ANDB RESTING ON TWO BRACKETS, BEARS 5ØN WEIGHT 0.5M FROM END A AND 150N WEIGHT 2M FROM FIRST WEIGHT. FIND THE REACTION FORCES AT B AND A. FB FA A
A 1260 N uniform beam is attached to a vertical wall at one end and supported by a cable on th other end. A 1960 N crate hangs from the far end of the beam. Using the info on the diagram find the following: a) Magnitude of the tensiossnj on the cable b) the horizontal components of the varce that the wallexerts on the beam c) the vertical components of the force that the wall exerts on th eleft end of the bean