A V-Belt drive is designed so that it has the input sheave on the shaft of an electric motor (normal torque) rated at .55 hi at 1160 rpm full-load speed. The drive is to a bucket elevator that is to be used 12 hours daily at approximately 675 rpm. The center distance is about 19.5 in. Add the detailed steps of your design to your attached worksheet. Hints: 1) In your design choose an appropriate belt section, specify the small pulley diameter, the large pulley diameter and the length of the belt. Determine the Belt length in inches, in two significant figures. Please enter below a numerical value only, no units are needed.

A V-Belt drive is designed so that it has the input sheave on the shaft of an electric motor (normal torque) rated at .55 hi at 1160 rpm full-load speed. The drive is to a bucket elevator that is to be used 12 hours daily at approximately 675 rpm. The center distance is about 19.5 in. Add the detailed steps of your design to your attached worksheet. Hints: 1) In your design choose an appropriate belt section, specify the small pulley diameter, the large pulley diameter and the length of the belt. Determine the Belt length in inches, in two significant figures. Please enter below a numerical value only, no units are needed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a driver shaft to be used with the following belt drive. Assume the shaft is simply supported by two bearings at both ends, and the effective diameter for the driving pulley is 100 mm. Do the following 1) Sketch shaft layout 2) Select Shaft components required to lock the axial position of the pulley and allow torque transmission 3) Size the driver shaft diameter and length if the driving torque is 5 Nm. And rotation speed of 1500 rpm. You are free to choose your own material **** Use DE-Goodman criteria for sizing and make sure that the shaft works within its critical speed.*** Answer: DRIVER SHAFT Design this driving shaft Shaft A SLACK SIDE TIGHT SIDE M R DRIVEN SHAFT
Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a distance of 12 m from the driving pulley of 480 cm diameter ?
Hello, I hope you can help me. I'm trying to create a device that has a spinning axle and I need to change the rotational force to be perpendicular to the axle. I know there are gears that can fit together have teeth, like the attached picture. I know there are other types of mechanisms, and some are more creative. But I also need for the solution to be low friction. What are 2 low friction methods of changing the directional rotation of a power axle 90 degrees? The entire creation is small, probably 12" x 12" Thanks for your help.
Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.
The BAPCO in Bahrain is looking to design a V belt drive system for its recently installed rotary machines. The smaller pulley having a diameter of * d" is connected to an electric motor and run at a speed of nd. The belt is used to drive a larger pulley at a speed of 90 rpm. The V belt is used to transmits a power of 95 hp and ignore it in belt class selection process (Table 17.9). The service factor for the V belt drive system is 1.3 and the suggested factor of safety for the current design is 2.5. Smaller Pulley Diameter = d = 9 in Speed of smaller pulley = nd = 900 rpm Design and select a V belt drive system.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
A belt drive consists of a flat belt stretched between two pulleys of equal diameter, 400mm, as shown in Figure Q1(a). The belt drive transmits a power of 250 W when the pulleys rotate at 150 rpm. The coefficient of friction between the belt and the pulley is 0.3. 400 mm Figure Q1(a) a) What is the value of the belt speed? b) What is the value of the effective tension transmitting power, T1-T2? c) What is the value of the ratio between the tight and slack tension, T1/T2? d) Use your answers to (b) and (c) to compute the individual values of T1 and T2. The belt has a density of 0.005 kg/cm3 and has a rectangular cross-section with width 5 cm and thickness 0.8 cm. The belt's maximum allowed stress is 50 N/cm2. e) Does the belt exceed its maximum allowed stress? Justify your answer.
3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving wheel = 1440rpm Speed of driven wheel = 400rpm Diameter of driving wheel = 300mm Center distance = 2500mm Service = 16hrs/day
The following drive system is used to raise a load at constant velocity. The motor rotational speed is 1000 rpm, and the rotational speed of the drum is 200 rpm. The efficiency of the gear box is 0.85. The efficiency of the drum is 0.95%. The moment of inertia of the motor (input shaft) is 0.5 kg.m², and the moment of inertia of the drum (output shaft) is 0.75 kg.m². Calculate: (1) The total (equivalent) moment of inertia of the drive system referred to the motor shaft. (2) The developed mechanical power on the motor Drum, 0.5 m diameter shaft. 1000 Kg Motor Gearbox
For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input speed is 870 RPM and input power is 25 HP. Nominal output speed is 310 RPM. Design a V-belt drive and specify:(a) (b) (c) (d) (e)the belt size,the sheave sizes,the number of belts, theactualoutputspeed,the center distance. Show all your calculations.
Please solve ellaborately and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You! Two shafts 30 in. apart, each carrying a four-step pulley, are to be connected by a crossbelt. The driving shaft is to turn 180 rpm while the driven shaft is to turn 50, 150, 250,and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find (a) the diametersof all the steps, (b) angle of contact for each pair of pulleys, and (c) belt length.