A turbojet is flying with a velocity of 900 ft/s at an altitude of 20,000 ft, where the ambient conditions are 7 psia and 10°F. The pressure ratio across the compressor is 13, and the temperature at the turbine inlet is 2320 R. Assume ideal operation for all components and constant specific heats for air at room temperature. The properties of air at room temperature are Cp = 0.24 Btu/lbm-R and k=1.4. Determine the propulsive efficiency.

A turbojet is flying with a velocity of 900 ft/s at an altitude of 20,000 ft, where the ambient conditions are 7 psia and 10°F. The pressure ratio across the compressor is 13, and the temperature at the turbine inlet is 2320 R. Assume ideal operation for all components and constant specific heats for air at room temperature. The properties of air at room temperature are Cp = 0.24 Btu/lbm-R and k=1.4. Determine the propulsive efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a turbojet engine, what are the assumptions for static & stagnation temperatures and pressures for the stators and rotors in both the turbine and compressor thanks
Plz answer this ASAP thx,before this someone has answered, only the picture doesn't appear From a Brayton cycle, the air entering the compressor has a temperature of 300 K, a pressure of 100 kPa and an air flow rate of 6 kg/s. The compressor pressure ratio is 10. The temperature of the working fluid entering the turbine is 1400 K. The efficiency of the turbine and compressor is 80% and the efficiency of the regenerator is 80%. Calculate A. thermal efficiency, B. workback ratio, C. power produced
Change the question's data and suggest and then solve it :- Q/ The minimum pressure and temperature in an Otto cycle are 100 kPa and 27°C. The amount of heat added to the air per cycle is 1500 kJ/kg. ii /Determine the pressures and temperatures at all points of the air standard Otto cycle. (i) Also calculate the specific work and thermal efficiency of the cycle for a compression ratio .of 8: 1 Take for air: c = 0.72 kJ/kg K, and .7= 1.4
A turbojet-powered aircraft is flying at 220 m/s and 8000-m altitude, where the ambient temperature and pressure are 236K and 35kPa, respectively.The pressure ratio of the compressor is 6 and the turbine inlet temperaturer is 970k. Estimate the thrust developed by the engine when the air flow rate is 55kg/s. employ an air standard-cycle analysis using the constant-pressurree specific heat c_p and specific heat ratio γ for air and neglecting the fuel properties.
An iseal Brayton cycle has a pressure ratio of 6:1. The temperature of the air is 22 degrees celsius at the inlet to the compressor and 1080 derees celsius at the inlet to the turbine. Take specific heat at constant pressure and constant volume for air as 1,006 KJ/kg K and 0,717 KJ/kg K respectively. Calculate: 1. the compresion absolute temperature to one decimal place 2. the work ratio of the plant to three decimal places 3. the specific work output to the turbine and specific work input to the compressor , to one decimal place and SI unit 4. the thermal efficiency of the plant to one decimal place
An ideal Brayton cycle has a pressure ratio of 7:1. The temperature of the air is 34 °C at the inlet to the compressor and 1080 °C at the inlet to the turbine. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the compressor exit absolute temperature to one decimal place and place the correct unit.
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 oC. the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
An ideal gas Diesel engine, that has an inlet temperature, pressure and compression ratio of 21 0C and 102 kPa 19:1 respectively. The maximum cycle temperature is 1,234 0C. Take Specific heat at constant pressure and constant volume for air as 1.005 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the specific heat rejected during the cycle to one decimal place and include the correct SI unit.
Required information A turbojet is flying with a velocity of 900 ft/s at an altitude of 20,000 ft, where the ambient conditions are 7 psia and 10°F. The pressure ratio across the compressor is 13, and the temperature at the turbine inlet is 2350 R. Assume ideal operation for all components and account for the variation of specific heats with temperature. Determine the velocity of the exhaust gases. (You must provide an answer before moving on to the next part.) The velocity of the exhaust gases is I ft/s.
QI/Calculate the power in kilowatts of the gas turbine power plant has a greatest temperature of 700°C and a pressure ratio of 10. The isentropic efficiencies of the turbine and compressor are 0.85 and 0.82 respectively. The mass flow rate of the air that inlet to the compressor is 15 kg/s at 15 °C. At the expansion process take Cp= 1.11 kJ/kg:K, y=1.333, and at the compression process take c,= 1.005 kJ/kg K, and y =1.4
An ideal gas Diesel engine, that has an inlet temperature and pressure of 19 0C and 102 kPa respectively with a compression ratio of 23:1. The maximum cycle temperature is 1,237 0C. Take Specific heat at constant pressure and constant volume for air as 1.005 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the specific heat received to one decimal place and include the correct SI unit.
An ideal diesel cycle powered by air has a compression ratio of 20. At the beginning of the compression process, the pressure of the air is 100 kPa, the temperature is 20 °C and the highest temperature of the cycle must not exceed 2250 K. Show the cycle in the P-v diagram.Then calculate: a) The heat entering and leaving the cycle, the thermal efficiency of the cycle, b) the average effective pressure of the cycle. Assume that specific heat is constant at room temperature constant at temperature. k=1.4 CP=1.005 kJ/kgK CV=0.718 kJ/kgK R=0.287 kJ/kgK