A tension member is composed of two 4x10 plates. They are connected to a gusset plate with the gusset plate between the two tension member plates, as shown in Figure 4. A36 steel is used, and 1-inch-diameter bolts are used. Determine the nominal strength based on the net section. ਜਨ ਨਾ OOO O 5² +2² O O Figure 4 Two plates, each plate 3/4 in. thick

A tension member is composed of two 4x10 plates. They are connected to a gusset plate with the gusset plate between the two tension member plates, as shown in Figure 4. A36 steel is used, and 1-inch-diameter bolts are used. Determine the nominal strength based on the net section. ਜਨ ਨਾ OOO O 5² +2² O O Figure 4 Two plates, each plate 3/4 in. thick

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Similar questions

Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Design the size and length of Fillet weld for the lap joint shown below, Use SMAW E70XX process, plates are A-36 steel? 90k LL 40k DL R-X7 5" Gusset P 8 90k LL 40k DL
A bolted connection shown consists of two plates 300mm x12mm connected by 4 - 22 mm diameter bolts. Edge distances = 75mm dhole for tensile and rupture = db + 3 mm dhole for bearing strength for Lc = db + 1.5 mm Fy = 248 Mpa Fu = 400 Mpa Fn = 330 Mpa Use LRFD design method. Determine the design strength due to the gross yielding of plates. (kN)
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
A plate 400 x 12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate is A36 steel. Assume allowable tensile stress on net area is .60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths
The plate with dimension 18 mm x 400 mm (thickness by width) is to be connected to a gusset plate using 6-Ø24 mm bolts in arrange in 3 row (2 each row) along the x-axis. The plate is to be design for tension. Using A36 steel and assuming Ae= An. Use NSCP 2015. a. Compute the design strength considering yielding and tensile rupture. (LRFD) b. Compute the allowable strength considering yielding and tensile rupture. (ASD)
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mm
The connection shows a PL10X200 loaded in tension and welded to a gusset plate 10mm thick. Calculate the following, assuming A992 steel is used. Use U =0.85. The weld thickness is ómm and the electrode is E70 (485MPA). PL 10 X 200 350mm What is the allowable weld connection strength (kN)?
What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 www 60mm 777 50mm 8mm P