A standard truck moves across a 25-meter span. The wheel loads areP1=36 kN and P2=142 kN separated by4.3 m and P3=142 kN at 7.6 m fromP2. Determine the beam dimensions ifthe maximum flexural stress is equalto 100 MPa. Use the ratio h = 1.6b.Round your answer into the nearestwhole number.O 213 mm x 415 mmO 415 mm x 213 mmO 321 mm x 514 mmO 514 mm x 312 mm

Given: The distance between wheel, x = 4.3 m The distance between load 2 and 3, y = 7.6 m The…

A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated b 4.3 m and P3=142 kN at 7.6 m from P2. Determine the beam dimensions the maximum flexural stress is equal to 100 MPa. Use the ratio h = 1.6b. Round your answer into the nearest whole number.

A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated b 4.3 m and P3=142 kN at 7.6 m from P2. Determine the beam dimensions the maximum flexural stress is equal to 100 MPa. Use the ratio h = 1.6b. Round your answer into the nearest whole number.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Related questions

Q: A four-cylinder, two-stroke 2.4-L diesel engine that operates on an ideal Diesel cycle has a…

Q: A mini-converter is used __.a. on small vehicles where a normal converter willnot fit properlyb. on…

A: Mini convertor is a device used in the diesel engines. This device is very important device in the…

Q: b) Determine the March number of the bullet for both medium.

A: (b) Consider the helium gas and calculate the speed of sound in helium. cHe=γRTMFor γ,…

Q: Determine the final velocity of car Initial velocity=7 m/s Acceleration=2.22 m/s2 Time=5 s

A: Given data : Time t=5 s Initial velocity U=7 m/s Acceleration a=2.22 m/s2 Required : Final…

Q: 1. Determine the force in members CD, CJ, and DJ. 401b B 8000 lb C D E 5001b L K . . . . . . . G 12

Q: 4. A round steel shaft rotates at 200 rpm while delivering 5000 W to a gear producing a bending…

Q: Neglecting friction, determine the tension in cable ABD and the reac- tion at C when = 60°. B A a- C…

Q: B 2² 3' E From the given A-Frame shown above, which statements are true: a. The horizontal reaction…

A: To find: Which of the options given are true.

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown. It is…

Q: Find the boiler heat transfer including the reheat process (kW)

Q: Compute the efficiency of machine Input=870 J Output=600 J

Q: For the binary cycle shown, the enthalpies are h1 - 3,185 kJ/kg: h2-2,206 kJ/kg; h3 - 178 kJ/kg: h4…

A: h1=3185 kJ/kgh2=2206 kJ/kgh3=178 kJ/kgh4=184 kJ/kgha=358 kJ/kghb=274 kJ/kghc=112 kJ/kghd=113…

Q: A rough, growling noise that is heard from a transaxlewhile it is in neutral with the engine…

A: The clutch is engaged, the engine is running, and the gearshift is in neutral. One of the most…

Q: surface hardening. In the steel available at the lab, 0.15%C plain carbon steel, 0.25% and mariging…

A: Ductile irons are austempered to create a special material with exceptional qualities of high…

Q: What is the lowest acceptable amperage setting for GTAwelding?

A: Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding…

Q: Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is…

Q: 6. 7. 8. 2. 11. 16. 17. 10. 12. ILLI (m) 1. 1,700,000 mV 2400000 9. 0.889 mA 3. 357,000 mA 4. 666000…

Q: An airplane has a half-wingspan of 26 m. Determine the change in length of the aluminum alloy [a =…

Q: Can we use this pump to supply water to an elvation 35 meters above? Explain your answer.

A: Given: Water Pump with manufacturer specifications

Q: 1. For the spring system given in Figure 1; Number the elements and nodes; i. ii. Assemble the…

Q: A fluid is pumped at a rate of 0.00156 m³/s through a 0.025-m-diameter pipe to fill a water tank as…

Q: Compute the efficiency of machine Input=870 J Output=600 J

Q: Find the maximum shear stress in rectangular section if normal shear stress value is 22 Mpa

A: Given data : Normal shear stress =ζ ζ=22 MPa Required : Maximum shear stress

Q: Stainless steel Iss Nuclear waste 9, w aconv T5,0 -Tsi • Constant properties • Negligible radiation…

Q: Determine the power required (Watts) to drive a reciprocating pump running at 1 rps and discharges…

A: Given data: N=1 rpsρ=850 kg/m3Q=369.2 gpm=0.0233 m3/sd=250 mmL=500 mmH=28 m Need to determine the…

Q: Prob. 3.6-10. The pipe-sleeve element (1) and cylindrical- rod core element (2) in Fig. P3.6-10 are…

Q: 300 kJ of thermal energy is stored at a temperature of 1000 K. Assuming perfect heat transfer to a…

Q: 3. Air enters a converging-diverging nozzle at 1.50 MPa and 900 K with a negligible velocity. The…

A: A converging diverging nozzle is a type of nozzle to produces an exhaust thrust with the help of the…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

Q: A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and…

A: Given data Pressure at bottom dead center = P1 = 1.3 bar Compression Ratio = CR = 1.5 x 10 = 15…

Q: What forms the basis for the AWS identification systemfor nonferrous covered electrodes?

A: The welding industry has adopted the American Welding Society’s(AWS) classification number series…

Q: The aluminum machine part is subjected to a moment of M = 75 N.m. (i) Determine the bending stress…

Q: A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and…

Q: 5. Figure 3, below, shows a rollercoaster ride. The curve of the rollercoaster is given by the…

Q: What are the four basic parts of a process plan?

A: A process plan basically contains a detailed list of the operations to be performed, standards used…

Q: Bodies A and B are joined by a cord parallel to the inclined plane as shown. Under body A which…

Q: 9.42. In an established flow in a pipe of 0.3 m diameter the centerline velocity is 3.05 m/s and the…

A: Given: d = 0.3 m u=2.73 m/s u=3.05 m/s y= 75 mm = 0.075 m

Q: What is a cost advantage of using preformed parts in afabrication?

A: A preform is an intermediate product that is subsequently blown into a polyethylene terephthalate…

Q: 1.52 Given that P - 120 lb and Q - 130 lb, find the rectangular representation of P+ Q. 12 Figure…

Q: A fluid is pumped at a rate of 0.00156 m³/s through a 0.025-m-diameter pipe to fill a water tank as…

A: The term pressure drop is meant between the differences in two-point of a fluid carrying network.…

Q: PLEASE WRITE YOUR COMPLETE SOLUTION AND BOX THE FINAL ANSWER. THANK YOU. Determine the normal…

A: Given data: δ=0.5 mmTi=27°CTf=126°C Need to determine the normal stress and change in length of the…

Q: A four-cylinder, two-stroke 2.4-L diesel engine that operates on an ideal Diesel cycle has a…

Q: Evaluate the surface integral. /[(x + y + 2) ds, (x + y + z) ds, S is the parallelogram with…

A: Please refer to the detailed solution given below, Answer - Integral I = 405.96

Q: Determine the final velocity of car Initial velocity=7 m/s Acceleration=2.22 m/s2 Time=5 s

A: Given : initial velocity , u = 7 m/s acceleration , a = 2.22 m/s2 time, t = 5 s To find : final…

Q: Study the figure below. Use the shear and moment diagram. Calculate the maximum moment. 265 kN 245…

Q: PROBLEM 1: A car travels a 10-degree inclined road at a speed of 20 ft/s. The driver then applies…

Q: = 2. The bending stresses on an element are: om = 25,00 psi or= 21,667 psi. There is a stress raiser…

A: ASME ellipse criterion:- ASME ellipse criterion is a theory of failure used to design component…

Q: Explain the operation of the circuit presented below. For each component, indicate name, drive mode,…

A: Given : To find : Working of the circuit

Q: The figure shows the EGL and HGL of a fluid as it enters a pipe and passes trough a vena contracta…

A: given; why head loss does not occur immediately instead of downstream?

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A standard truck moves across a 25-
meter span. The wheel loads are
P1=36 kN and P2=142 kN separated by
4.3 m and P3=142 kN at 7.6 m from
P2. Determine the beam dimensions if
the maximum flexural stress is equal
to 100 MPa. Use the ratio h = 1.6b.
Round your answer into the nearest
whole number.
O 213 mm x 415 mm
O 415 mm x 213 mm
O 321 mm x 514 mm
O 514 mm x 312 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 16.2 mm, determine the second moment of area of the cross section. Note: Give your answer in mm4 Note: Do NOT include units in your answer. 10MM 150HM 120 MM hmm
A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm. If there are no other loads applied to the beam (My, P, Vy and Vz = 0), what is the normal stress at point F? Give your answer in kPa to two decimal places with negative indicating compression and positive indicating tension. b/4 М, h E Ihis F h/3 В M. D b/4
The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 11.7 mm, determine the second moment of area of the cross section. Note: Give your answer in mm4 Note: Do NOT include units in your answer. 10HH 150MM Answer: 120 hmm
W 8 L/2 1/2 Wz
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P=1623N, T=4552Nm, a=0.77m, b=1.13m, c=0.78m, w=39mm, and h=80mm. Round off the final answer to five decimal places. Show your complete solution.
The beam AB in the figure supports a load which varies from an intensity of 50 KN per linear meter to 200 KN per meter. 8.2 Determine the location of the resultant load from point A. 200 KN/m 50 KN/m B 6 m
w1 B w2 Determine the shear force and bending moment at the one-third, middle, and two-thirds of the length of the beam (from point A), respectively. Use wl = 7 kN/m, w2 = 4 kN/m, and a =4 m. The shear force at the one-third of the length of the beam (from point A) in kN is (round to the nearest integer): kN The shear force at the middle of the length of the beam (from point A) in kN is (round to the nearest integer): KN The shear force at the two-thirds of the length of the beam (from point A) in kN is (round to the nearest integer): |kN The bending moment at the one-third of the length of the beam (from point A) in KN.m is (round to the nearest integer): kN.m The bending moment at the middle of the length of the beam (from point A) in kN.m is (round to the nearest integer): kN.m The bending moment at the two-thirds of the length of the beam (from point A) in kN.m is (round to the nearest integer): kN.m
A cable with supports at the same elevation has a span of 400 m. The cable supports a uniformly distributed load of 6 kN/m along the horizontal. The maximum ten- sion in the cable is 5000 kN. Determine The angle between the cable and the horizontal at a support.
Determine the extension (m) of the whole system shown if k1 = 14.7 N/m, k2 = 21.23 N/m, k3 = 38.22 N/m, k4 = 48.78 N/m, and k5 = 52.73 N/m and a force of 62.11 N is applied. (Use 2 decimal places for the final answer.)
Determine the extension (m) of the whole system shown if k1 = 14.28 N/m, k2 = 28.89 N/m, k3 = 37.72 N/m, k4 = 41.16 N/m, and k5 - 51.08 N/m and a force of 65.48 N is applied. (Use 4 decimal places for the final answer.) ki ka k3 F
Determine the shear force 7.5 ft to the right of point A for the beam shown belowif T = 1080 lb ft, W = 176 lb/ft, a = 5.44 ft, b = 3.53 ft, = 3.51 ft. Round of the final answer (in lb) to four decimal = places. W A D B C T ★b.c a ➜
w2 w1 Determine the shear force and bending moment in the beam. Use wl = 4 kN/m, w2 = 7 kN/m, a = 4 m, and b =4 m. The shear force at the point B of the beam in kN is (round to the nearest integer): kN The bending moment at the point A of the beam in kN.m is (round to the nearest integer): kN.m The bending moment at the point B of the beam in kN.m is (round to the nearest integer): kN.m The bending moment at the point C of the beam in kN.m is (round to the nearest integer): kN.m The location of the maximum bending moment from the point A of the beam in meter is (round to the nearest integer): meter The maximum bending moment of the beam in kN.m is (round to the nearest integer): kN.m