A single acting reciprocating pump has a bore of 15 cm and a stroke of 30 cm. The suction pipe has a diameter of 10 cm and is fitted with air vessel. Find the rate of flow into or from air vessel at 0 = 30° and 90°. Also find crank angle at which %3D there is no flow into or from air vessel. The pump runs at 120 rpm and the piston has S.H.M.

A single acting reciprocating pump has a bore of 15 cm and a stroke of 30 cm. The suction pipe has a diameter of 10 cm and is fitted with air vessel. Find the rate of flow into or from air vessel at 0 = 30° and 90°. Also find crank angle at which %3D there is no flow into or from air vessel. The pump runs at 120 rpm and the piston has S.H.M.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Petlon Wheel having semicircular buckets and working under a head of 150 m runs at a speed of 600 rpm. If the discharge through the nozzle is 45 lit/s. Find the power available at the nozzle and the hydraulic efficiency. Take wheel diameter as 0.5 m and C,, for the nozzle as 0.98.
18. A centrifugal pump has, to work against a head of 25 metres at a speed of 850 rpm.. The flow component of the velocity at outlet is 2 5 metres/second. The outlet vane angle is 40°." If the discharge of the pump is 0-25 cumec find (i) The diameter of the impeller and (ii) The width of the impeller at outlet. Neglect losses. (0:387 m; 0*082 m)
A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per sccond. The velocity of flow is 1 m/s and the vanes are curved back at outlet at 30° to the wheel tangent. If the impeller speed is 400 r.p.m., find the power to drive the pump. (Ans. 12-9 kW) 3.
a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
A Centrifugal pump is to discharge water at the rate of 110 lits/sec at the speed of 1450 rpm agalnst head of 13 m. Impeller diameter is 250 mm and its width is 50 mm. If manometric efficiency is 75%, determine vane angle at outer periphery.
In reaction turbine has outer and inner diameters of the wheel as (1m) and (0.5m) respectively. The vanes are radial at inlet and the discharge is radial at outlet and the water enters the vanes at in angle of (10o). Assuming the velocity of flow to be constant and equal to (3m/s) find the speed of the wheel and the vane angle at outlet.
Q-- Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Please help me in finding the solution of the problem below with a given answer. This will help me to review. Thank you Question: A centrifugal pump has impeller with dimensions r1 = 71 mm, r2 = 154 mm, b1 = 52 mm, b2 = 26 mm, β1 = β2 = 30º. For discharge of 74 L/s and shockless entry to vanes, compute the speed in rpm.Answer 743.12
An inward flow reaction turbine, having an inner and outer diameter of 0.45m and 0.90m, respectively. The vanes are radial at inlet and the discharge is radial at outlet and the water enters the vanes at an angle of 12°. Assuming the velocity of flow as constant and equal to 2.8m/s, find the speed of the wheel and the vane angle at outlet. Show schematic diagram and provide solutions.
Find the specific speed of a double suction centrifugal pump delivering 1.5 m³/s against a net head of 15 m when running at 725 r.p.m. state the type of impeller to be employed for this pump.
A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow velocity through the impeller having radial vanes is constant at 3.0 m/s. The speed of the pump is 1200 rpm and manometric efficiency is 85%. Find the head developed by the pump (m) 19:54 /
A double acting cylinder is hooked up in the regenerative circuit. The relief valvesetting is 105 bars and the pump flow is 0.0016m˄3 / s. If the regenerative and retractingspeed are equal to 0.25m/ s, find the piston and rod area and also load- carrying capacityfor the:a. Extending strokeb. Retracting stroke