A simply supported beam made of W21x62 with a span of 8 m is subjected to counterclockwise moment at the left support and a counterclockwise moment at the right support. The moment at the right support is 1.5 times that at the left support, both bending about the strong axis. Assuming A36 steel, determine the following:

A simply supported beam made of W21x62 with a span of 8 m is subjected to counterclockwise moment at the left support and a counterclockwise moment at the right support. The moment at the right support is 1.5 times that at the left support, both bending about the strong axis. Assuming A36 steel, determine the following:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.5.10P: .10 A built-up bourn supporting a condominium balcony is made up of a structural T (one half of a W...

See similar textbooks

Similar questions

.10 A built-up bourn supporting a condominium balcony is made up of a structural T (one half of a W 200 x 31.3) for the top flange and web and two angles (2 L 2 / b / 6.4. long legal back-lo-backl lot the bottom flange and web. as shown. The beam is subjected to a bending moment .1/ having its vector at an angle ft lo the z axis (see figure). Determine the or ion ta I ion of the neutral axis and calculate the maximum tensile stress ir, and maximum compressive stress tr. in ".he beam. .Assume that 9 = 30°andM = 15 kN · m. Use the numerical properties: c =4.111mm, c2 =4.169 mm, of = 134 mm, I, = 76 mm, A = 4144 mm 3 =3.88 X 106 mm 4, and = 34.18 X 10 mm 4.
A beam of length L is designed to support a uniform load of intensity q (see figure). If the supports of the beam are placed at the ends, creating a simple beam, the maximum bending moment in the beam is qL2/8. However, if the supports of the beam are moved symmetrically toward the middle of the beam (as shown), the maximum bending moment is reduced. Determine the distance a between the supports so that the maximum bending moment in the beam has the smallest possible numerical value. Draw the shear-force and bending-moment diagrams for this condition. Repeat part (a) if the uniform load is replaced with a triangularly distributed load with peak intensity q0= q at mid-span (see Fig. b).
A simple beam AB supports two connected wheel loads 3P and 2P that are a distance d apart (see figure). The wheels may be placed at any distance x from the left-hand support of the beam. (Assume P = 12 kN, d = 2 m, and 1 = 15 m.) (a) Determine the distance .y that will produce the maximum shear force in the beam, and also determine the maximum shear force Vmax. (b) Determine the distance v that will produce the maximum bending moment in the beam, and also draw the corresponding bending-moment diagram.
A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
From the figure shown: X1 q=15 kN/m X2 10m. ********** x1 What is the moment at midspan if X1 = 2 m. Find the distance x₁, if the moment at midspan is zero. 3 Determine the distance x2 so that the maximum moment in the beam is the least possible value.
From the given beam shown below, find the moment value on segment CD (MCD). 40 kr/m 75kum Im Дв ↓ Im
2. • Determine the reactions for Beam 2 • Draw the Shear Force and Bending Moment diagrams • Calculate the Maximum Moment and determine its position on the Beam 2 10kN/m 2500 + Пв 2000 7500 Beam 2 25kN c MIRO 1500 1500 30KN E
1. The cantilever beam AH is acted upon by a uniformly distributed downward load of intensity 4P/L(force/length)between A and B, a concentrated moment M-2PL at C, and a vertical force Pat D. Using P=20kN and L=1.2 m, construct the shear force and bending moment diagrams for the beam. Mark numerical values for points A through H, along with max/min values on these diagrams. 4P/L Mo L/4 L/4 L/4 L/4 A C H V(x)/P M(x)/PL
ASAP
Determine the internal normal force and shear force, and the bending moment in the beam at points C and D. Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. For your explanation section, complete a FBD of the other side of the beam from the version you did to solve the problem. 8 kip 40 kip · ft A to to D B- 8 ft 8 ft- -8 ft
3. For the beam shown, find the reactions at the supports and plot the shear-force and bending moment diagrams. Label the diagrams properly and provide values at all key points. y O 1.2 m R₁ 4 kN A 1 m AB R₂ 1 m 2 kN с X
3. The 3-meter long T-beam pictured on the far right is placed flange downwards and subjected to the loading shown below. Sketch the moment diagram and calculate the maximum compressive and tensile bending stresses. 18 kN/m 12 kN/m ✓ Y Y 3 m B 30 mm, с. B 150 mm M 150 mm 300 mm 1 30 mm