Question 1A multi plate clutch has three plates and four pressure plates, pressed together byan axial force of 500N. µ = 0.3. The outer radius of the plates is 100mm, and theinner radius is 80mm. Calculate the torque that the clutch can transmit.If the inner radius and axial force are to remain the same, but the torque is increasedby 25%, what must the outer radius than be?(use uniform wear theory)

Since the given clutch is a multi-disk clutch, the relation for the torque transmitted by the clutch…

Answered: A multi plate clutch has three plates…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. Determine the minimum pressure in a plate clutch where the axial force is 1300 lb, the inside radius of contact is Ri = 2.5 in, the outside radius is Ro = 5 in. Uniform wear is assumed.
A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm respectively. Calculate the force required to press the two halves together if it is to transmit 250 W at 650 rpm. Use both the uniform wear theory and uniform pressure theory
A multiplate disc clutch transmits 75 kW of power at 2000 rpm. Coefficient of friction for the friction surfaces is 0.2. Axial intensity of pressure is not to exceed 180 kN/m?. Internal radius is 100 mm and is 0.8 times the external radius. Find the number of plates needed to transmít the required torque. Assume uniform wear conditions.
A A multiple disc clutch transmits 55 kW of power at 1800 r.p.m. The coefficient of friction is 0.1 and the axial intensity of pressure is not to exceed 160 kN/m. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque.
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.
4) In a single plate clutch both sides are effective. The clutch transmits 10 Kw power. The maximum torque is 120 Nm, the maximum axial force should not be more that 100 KN/m2. The outer diameter of the clutch plate is 1.3 times of the inner diameter. Find out the axial load exerted by the spring and outer and inner diameters of the clutch plate.
A disc clutch has 6 pairs of contacting friction surfaces. The frictional radius is 2 inand the coefficient of friction is 0.30. An axial force of 100 lb acts on the clutch. Theshaft speed is 400 rpm. What is the power transmitted by the clutch?
Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to transmit 110 kW at 1250 r.p.m. The outer diameter of the contact surfaces is to be 300 mm. The coefficient of friction is 0.4. (a) Assuming a uniform pressure of 0.17 N/mm? ; determine the inner diameter of the friction surfaces. (b) Assuming the same dimensions and the same total axial thrust, determine the maximum torque that can be transmitted and the maximum intensity of pressure when uniform wear conditions have been reach.
A conical Clutch transmits rotation from one rotating shaft to another though frictional forces on the conical face. The following data is for a conical clutchInside Diameter 25.0 mmOutside Diameter 100 mmCoefficient of Friction 0.33Axial Force 1000NIncluded angle 100 degreeRotational speed 1500rev/minuteCalculate the Torque and Power that can be transmitted without slipping using both Uniform Pressure Theory and Uniform Wear Theory
(7) A clutch system is to be designed to transmit 800 ft-lb of torque. A multi-plate clutch in an oil bath is found to be suitable for this application. The outer disk diameter is to be limited to a maximum of 7 inch. Design data for molded friction material and steel disk is Pmax = 160 psi and f = 0.11. Determine inner diameter of disks, clamping force and number of disks. Assume inner diameter of disk = 0.5 * outer diameter. Assume uniform rate of wear at interface (List necessary assumptions, make suitable sketch & label it, write conclusions).
A single disc clutch is used to transmit 12kW power at 1000rpm. The axial pressure is limited to 0.08 N/mm2. If the external diameter of the friction lining is 1.25 times the internal diameter, find the required dimensions of the friction lining. Assume uniform wear conditions. The coefficient of friction may be taken as 0.3.
A wet disk clutch is to be designed to transmit 150 Nm of torque at 1200 rpm using 4 pairsof sintered lining with a maximum pressure at 1.8 N/mm² and the coefficient of friction as0.06. Assume uniform wear, compute the following:i.The required inner and outer diameters of the sintered lining if the internal diametershould be 0.577 of the external diameter.ii.The number of disks needed.iii.The power transmitting capacity.iv.The axial force exerted by the springs to keep the clutch engaged.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS