A lapped bolted tension member is shown. Diameter of bolts are 22 mm and the plate material is A36 steel Fy = 275 MPa, Fu = 415 MPa. Assume the fasteners are adequate and do not control the tensile capacity. Diameter of hole is 2.5 mm bigger than the diameter of bolt. T12 50 75 35 50 50 100 100 50 50
Q: LV2, D 2g To estimate the frictional head loss, we use Darcy-Weisbach eq (he =f), where fis the…
A: To Determine Which of the given options are correct about sawmee equation and moody diagram.
Q: What is the reaction at A in kN? Replace the distributed loading by an equivalent resultant force…
A: Determine support reactions for given loaded beam.
Q: A 450-N is in contact with a level plane of fy = 0.10. The block is acted upon by a horizontal force…
A:
Q: Answer the situational problem. At a certain section of a river the left and right water edges are…
A: Hi! Thank you for the question, as per the honor code, we are allowed to answer three sub-parts at a…
Q: tangents of a S.
A:
Q: Determine the Deflection at the midspan of BC in millimeters unit. Use the Area Moment Method.…
A: Moment Area method: The moment area method is known as Semi graphical method. This method is used to…
Q: Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi…
A:
Q: What is the moment reaction at A in kN.m? kN Solve for the support reaction of the beam shown in the…
A: Find support reaction As only vertical load is acting, so horizontal reaction at support is zero.
Q: The tied three-hinged arch is subjected to the loading shown. Determine the components of reaction…
A:
Q: activities A1, A2, A3, A4, A5, A6, A7, A8, A9, and A10 sł durations provided under each activity.…
A: We need to determine Total Time of Project ES=Earliest Start Time EF=Earliest Finish Time LS=Least…
Q: 1. A car travels in a straight line. Initially, V, = 10 m/s. Then it accelerates uniformly at a, =…
A:
Q: Question 7: The moment diagram for a 20-ft span steel beam is shown below. There is compression…
A:
Q: At node A, water enters at a rate of 275li/s and flows out at 5 nodes with different rates namely:…
A: Solution At node A , Q = 275 l/s = 0.275 m3/s At node B , Q = 35 l/s = 0.035 m3/s At node C , Q = 80…
Q: 6 kN 4m 4m
A: Compute the shear and moment diagram of the given figure below. Show complete values in the…
Q: Problem 2. A storm had 3 successive 6-hr intervals of rainfall magnitude of 3.0, 5.0 and 4.0 cm,…
A:
Q: The uniform stone has a mass of W (in kg) and is hel in the horizontal position using a wedge at B.…
A:
Q: Problem 2 Compute the shear and moment diagram of the given figure below. Show complete values in…
A:
Q: column of 5m long whose one end is fixed , and other end is pinned with a slenderness ratio of 25…
A:
Q: vil Engineering The ordinates at 1-hr intervals of a 1- ydrograph are 15, 33, 56, 72, 44, 23, ms/mm.…
A: Given ordinates of 1 hr intervals First runoff R1 = 2 mm Second Runoff R2 = 1 mm Third runoff R3 =…
Q: For the loaded beam shown, using moment - area method. a. Determine the value of ElS at mid span and…
A: The free body diagram of the section is :
Q: Which among the formulas below can be used to compute the combined stress at the bottom fiber of a…
A:
Q: Q2. The compound beam shown in Fig.2. is pin supported at B and supported by rockers at triangle…
A:
Q: Determine the force in members CDof the truss in kN and state if the members are in tension or…
A: ASKED: To determine the force in member CD of the given truss and state the nature of the force.…
Q: The thickness of the capillary property band is larger in the case of It is formed from fine-grained…
A: Right. The height of capillary rise in the sediments in fine grained sediments is more than that in…
Q: The FC of a bridge is 200 M, annual malntenace cost is 200,000 and cost of bridge rehabilitation is…
A:
Q: A certain horizontal curve on a 6-lane highway (3 lanes each direction with no median) has a…
A: Radius of curve = R = 1494.9ft Radius of innermost lane curve = Rv = R - 12 - 12/2 = 1494.9 - 12 -…
Q: A CAST IRON COLUMN OF CIRCULAR SECTION HAS A PROJECTING BRACKET CARRYING A LOAD OF 200 KN AT A…
A: Calculation of Maximum and Minimum Stress in a column
Q: A horizontal pipe curves through a deflection angle of 60° and in the bend changes from 900 mm in…
A: Solution Diameter at section 1-1 = 900 mm = 0.9 m Diameter at section 2-2 = 600 mm = 0.6 m V1 = 2.4…
Q: Solve for the reaction at B.
A: This question has been taken from structural analysis
Q: Q-14: A soil has a void ratio of 0.70, degree of saturation 50% and G =2.7. Find the water content,…
A:
Q: I. Compute the centroidal distance with respect to x- and y- axis of the figures below. 3 in 4 in 6…
A:
Q: The arch structure is subjected to the loading shown. Determine the horizontal and vertical…
A:
Q: A ball is shot vertically into the air at a velocity of 60 m/sec. After 4 sec., another ball is shot…
A: Given -
Q: As a plant maintenance engineer, you are required to purchase a 3,000 L tank of liquid butane to…
A:
Q: For a falling-head permeability test, the following values are given: Length of specimen = 200 mm…
A: A falling head permeability test data is given and it has been asked to determine hydraulic…
Q: A B E -smt-sm-sm-5 m – Consider the beam in the figure without the applied load. If support C…
A:
Q: What is the reaction at B in kN? Replace the distributed loading by an equivalent resultant force…
A:
Q: Q.2 having k=I cm /sec, dia. =0.75 m, n = 0.33 for soill and k= 2 cm /sec, dia. =0.6m , n=0.28 for…
A: Given -
Q: 4. Three cylinders are piled in a rectangular ditch as shown. Neglecting friction, determine the…
A: Determine the reaction at cylinder A and the vertical wall.
Q: TP1 4.20 21+80 5.80 22+00 5.95 22+50 6.05 BM2 5.83 451.06 3. The bearing of line AB is N 50°16'08"…
A: 4. Answer Number of observation = 10 Most probable number = average of the observation…
Q: Determine the reaction at the roller sl 100 N 200 N 300 N 60 45 30 1 m 1 m
A:
Q: Estimate quantity of Steel Reinforced rebar of given plan below for the reinforced concrete beams as…
A:
Q: don't understand, can you provide more detailed steps,
A:
Q: The acceleration of a particle along a straight lne is defined by a (21- 4) m/s, where is in…
A: The given data is shown below: a=2t-9m/s2At t=0 sec, s=1 m, v=10 m/s
Q: An incompressible fluid is flowing at steady state in the annular region (i.e., torus or ring…
A:
Q: Q-14: A soil has a void ratio of 0.70, degree of saturation 50% and G =2.7. Find the water content,…
A: Given: Void ratio Degree of saturation Specific gravity To find: Water content Porosity Bulk…
Q: “c" mm 10 kN/m “c"mm BA "b" m "а" m "b" m “d" mm ((ур.)
A:
Q: Compound curve with I=54 11'40", IS=32 32'10", TS=812.25, DL=2°, IL=21 39'30", TL=1168, RS=1325.57,…
A: Compound Curve: A compound curve is a simple curve. A Compound Curve generally consists of two or…
Q: The three-hinged spandrel arch is subjected to the uniform load of 20 kN/m. Determine the internal…
A:
Q: Problem 2 Compute the shear and moment diagram of the given figure below. Show complete values in…
A: If any member has pin joint at both end than member behave as link ( zero moment and zero shear…
Step by step
Solved in 4 steps with 1 images
- Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
- Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The bracket is subject to an eccentric load of 150 kN. Use LRFD. Use A36 steel. Questions a) Determine the critical force on the most stressed bolt. b) Determine the nominal shear stress of the most stressed bolt.Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strengthA bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572 Grade 50 plate material has a width of 150 mm and thickness of 16 mm. Assume diameter hole to be 24 mm. Bolt threads are excluded from the shear plane. Allowable stress of A 325 bolts: Fv = 207 MPa Fp = 1.5 Fu (to prevent excessive hole deformation) Allowable stresses of A572 Grade 50 plate material: Fy = 345 MPa Fu = 450 MPa a. Compute the tensile capacity due to the failure of the plates. b. Compute the tensile capacity due to the failure of the bolts.
- Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONSPrepare an excel file and to find a) area of the bolt, b) Average Shear Stress Bolt c) Bearing Area Stress and d) allowable stress. Applied force range – 500 to 1000 N (in step of 100 N) Bolt diameter range – 10 to 25 mm (in step of 5 mm) Plate thickness – 10 mm Consider ultimate tensile strength as 460 N/mm2. And consider factor of safety as 1.5.
- The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets4. Calculate the design strength (ocPn) of W24X76 with length of 12 ft. and pinned ends. A572 Grade50 steel is used. E=29x103 ksi. Show your work in detail. ASTM Classification A36 A572 Grade 50 A992 Grade 50 A500 Grade B (HSS rect, sq) A500 Grade B (HSS round) A53 Grade B Yield Strength F, (ksi) 36 50 50 46 42 35 Ultimate Strength F (ksi) 58 65 65 58 58 60A plate 400 x 12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate is A36 steel. Assume allowable tensile stress on net area is .60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths