A cylindrical pressure vessel has an internal diameter of 2 m and is fabricated from plates 20 mm thick. If the pressure inside the vessel is 1.5 N/mm2 and in addition, the vessel is subjected to an axial compressive load of 2500 kN, calculate the normal and shear stresses on a plane inclined at an angle of 60⁰ to the axis of the vessel.

A cylindrical pressure vessel has an internal diameter of 2 m and is fabricated from plates 20 mm thick. If the pressure inside the vessel is 1.5 N/mm2 and in addition, the vessel is subjected to an axial compressive load of 2500 kN, calculate the normal and shear stresses on a plane inclined at an angle of 60⁰ to the axis of the vessel.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

The internal and external diameter of a thick hollow cylinder are 105 mm and 145 mm respectively. It is subjected to an external pressure of 40 N/mm2 and an internal pressure of 120 N/mm2. Calculate the radial and circumferential stresses at the mean radius.
A cylindrical steel pressure vessel 250 mm radius with a thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m². Calculate the tangential stress in the steel.
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. Find the longitudinal stress in the tank.
The wall thickness of a 1.2 m diameter spherical tank is 1.6875 mm. Calculate the allowable internal pressure if the stress is limited to 55 MPa. If i will get the same answer again I will report and downvote.
A cantilevered beam is loaded as shown. The cross section at the wall is shown, with points of interest A (at the top), B (at the center), and C (midway between A and B). 200 mm where F= 1.4 kN F B 50 mm 50 mm Cross section at wall NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
A steel tube of 200 mm external diameter is to be shrunkonto another steel tube of 60 mm internal diameter.The diameter at the junction after shrinking is 120 mmbefore shrinking on, the difference of diameters at the junctionis 0.08 mm. Calculate the radial pressure at the junctionand the Hoop stresses developed in the two tubes aftershrinking on.Take E = 2 x 10³ N/mm²
Calculate the minimum thickness of the vessel if the allowable tangential stress is 200 MPa. The diameter of the vessel is 1500 mm and the pressure inside the vessel is 10 MPa.
A cylinder of (320) mm inside diameter and (64) mm thickness is subjected to an internal pressure of 15 MPa. Find the variation of circumferential and radial stresses in the shell and plot them. What is the increase in the inside and outside diameters of the shell? Take E=200 GPa and v=0.3
A spherical pressure vessel 400 mm in diameter with a wall thickness of 15 mm is subjected to an internal pressure of 5 MPa. The modulus of elasticity of steel is 200 GPa. Calculate the stress in the wall of the container.
The wall thickness of the spherical tank is 8mm, calculate the diameter if the allowable stress is 140 MPa and the internal pressure is 60MPa.
The same circular plate, as in the previous questions, is considered. Assume a plate radius of Ro=490mm and a plate thickness of h=9.64mm, respectively. Also, assume that the plate is subjected to a uniform pressure of P=1,440 KPa, and that the plate is made of a material of Poisson's ratio V=0.34. Find the absolute value of the radial stress at the centre of the plate in KPa. NOTES: type in your answer without considering any negative sign; round-off your answer to 4 decimal places. ↓ r> P Ro VIT
A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram