7-2 Air and water flow at 0.08 kg/s and 0.32 kg/s respectively in a horizontal tube of inside diameter 25 mm. The mean pressure is 9.90 bar (absolute) and the pressure drop across a length of 5 m is 342 FLUID FLOW FOR CHEMICAL ENGINEERS 0.215 bar. What is the value of the friction factor? Assume isothermal conditions. Data: at 9.90 bar, VG = 8.28 x 10-2 m³/kg, V₁ = 1.02 X 10-3 m³/kg.

7-2 Air and water flow at 0.08 kg/s and 0.32 kg/s respectively in a horizontal tube of inside diameter 25 mm. The mean pressure is 9.90 bar (absolute) and the pressure drop across a length of 5 m is 342 FLUID FLOW FOR CHEMICAL ENGINEERS 0.215 bar. What is the value of the friction factor? Assume isothermal conditions. Data: at 9.90 bar, VG = 8.28 x 10-2 m³/kg, V₁ = 1.02 X 10-3 m³/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air (diatomic, MW = 28.8664 g/mol) at 1.7 atm gage (where Pam = 1 atm) and 15°C enters a 70-m long horizontal 75-mm-ID steel pipe (€ = 4.6(10) m). The velocity at the entrance of the pipe is 60 m/s. Assuming isothermal flow, what is the absolute pressure (atm) at the discharge end of the line? Use Churchill equation for the friction factor.
On a single plot, show curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure should be 0 to ~1 MPa). Pipe inner diameter: 0.03 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
A mixed berries cordial manufacturer changed to 5 m stainless steel tubing due to highamount of energy drop recorded in the previous material. Calculate the pressure drop permeter length for the cordial if relative roughness, velocity, density, viscosity, and friction inthe pipe are given as 0.0015, 1.5 m/s, 1120 kg/m3,1.6 X10-3 kg/m s and 0.07, respectively.
Pressure measurement will be carried out with Pitot tube in air flow with average speed 400 m/s, static pressure 0.8 bar and static temperature 15ºC. How many kPa is the total pressure measured by the Pitot tube, since R=287 J/kgK and k=1.4? a. 163.67 b. 182.57 c. 159.75 d. 187.05 e. 178.42
An ideal gas in which the pressure P is related to the volume V by the equation PV=60 m2/s2 flows in a steady isothermal flow along a horizontal pipe of inside diameter di =0,04m. The pressure drops from 0.5 atm to 0.35 atm in a 1000 cm length. Calculate the mass flowrate in kg/(sm2) if we can assume that the friction factor jf stay constant at a value of 5,2´10-3.
For axial flow through a circular tube, the Reynolds numberfor the transition to turbulence is approximately 2300 based on the diameter and average velocity. Ifd= 5 cm and the fl uid is kerosene at 20 ° C, fi nd the volumeflow rate in m 3 /h that causes transition.
A thin-plate orifice is used to measure water flow rate. The water temperature is 27 C and a mass flow rate of 50 lit/s is measured by the orifice. The pipe diameter is 26 cm and the orifice diameter is 7 cm. Find the non-rcoverable pressure drop. [Ans.: 21 m, Cd = 0.6, K = 2.5].
Frictional Pressure Drop in Flow of Olive Oil. Problem:Calculate the frictional pressure drop in pascal for olive oil at 293 K flowing through a commercial pipe having an inside diameter of 0.0525m and a length of 76.2m. The velocity of the fluid is 1.22m/s. Use the friction factor method. Is the flow laminar or turbulent?
Plot curves on a single plot that display the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure as 0 to ~1 MPa). Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
As a process engineer, you are designing a new drinking water treatment plant using conventional treatment process including Two Rapid Mixers as follows: The design flow is 50 million gallons per day (MGD) (1 Gallon = 3.785 L, 1 m³ = 1000 L). The average temperature of water is 5°C with a dynamic viscosity, μ = 1.519 x 10-3 Pa.Sec In each rapid mixer with a square shape, detention time, e = 1 min, water depth H = 13 ft, and power input P = 1.5 kw (1 ft = 0.3048 m, 1 KW = 1,000 W) The equivalent diameter, TE for each rapid mixer is ________ m. TE || AIR 1) 4.1 2) 4.4 3) 4.6 4) 4.8 5) 0.4
Answer this ASAP plz Air enters a pipe with a diameter of 3 cm and a length of 17 m with a speed of V1 = 75 m/s, pressure P₁ = 600 kPa and T₁ = 60 °C and a friction factor of 0.025. Count: a. V2, P2, T2 and po2 at the end of the pipe. b. What is the additional length of the pipe that causes the outflow to be sonic.
Z\0 @ P 0:10 ZAIN IQ II. Quiz 2 Thermo.pdf Gas flowing through a diverging nozzle has at inlet section a temperature of 20 °C, pressure 120 kN/m² and velocity 300 m/s. At the outlet of the nozzle the velocity has fallen to 100 m/s. Assuming an adiabatic flow, what is the values of outlet pressure, temperature, internal energy and specific enthalpy at outlet section. Take y= 1.333 and Cv= 0.86 kJ/kg K.