5.3 Water flows upward through the pipe reducer shown. The elevation difference betwoen points /and 2 is 4z. If the pressure gage mounted at point / reads gage pressure p, determine the volumelow rate Q in m/sec. Take the following data:MercuryA 18md- 100 mwa - 70 mmL- 180 mwa - 300PS8 barD - 200 mmIf the water flow is reversed downward having the same volume flow rate calculatedpreviously Q, determine the new inclined manometer reading, what do you notice.

Bernoulli's equation Bernoulli's equation states that, an increase in the speed of a fluid occurs…

5.3 Water flows upward through the pipe reducer shown. The elevation difference berwoen points / and 2 is de. If the pressure gage mounted at point / reads gage pressure p, determine the volume flow rate Q in mvec. Take the following data: Mercury A - L8m a - 70 mm D - 200 mm a - 0 d- 100 mm L I80 mm PSA bar If the water flow is reversed downward having the same volume flow rate caleulated previously Q. determine the new inclined manometer reading what do you notice.

5.3 Water flows upward through the pipe reducer shown. The elevation difference berwoen points / and 2 is de. If the pressure gage mounted at point / reads gage pressure p, determine the volume flow rate Q in mvec. Take the following data: Mercury A - L8m a - 70 mm D - 200 mm a - 0 d- 100 mm L I80 mm PSA bar If the water flow is reversed downward having the same volume flow rate caleulated previously Q. determine the new inclined manometer reading what do you notice.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through the pipe system as shown, mass flowrate A divides equally into B and C, and discharges to the atmosphere. 6 m/s 100 mm A 60 mm 60 mm 06 PROB_034 Cappri n n, Do the following: (A) Compute the mass flowrate at A, B and C (B) Compute the pressure in the pipe at A (C) Sketch the C.V. and FBD for the flow in the pipe section - label and identify all relevant components: coordinate directions, velocities, forces and/or pressures, inlet & outlet sections (D) Compute the x and y forces required to hold the pipe in the position shown
2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
B1. A water with viscosity 11.4x10-3 poise is flowing through a pipe of diameter 300 mm at the rate of 500 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1 km. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of water (in m/s) is The value of Reynold's Number is The frictional loss in the pipe (in m) is
Show complete solution. Units must be included in all calculations. All numerical values should be rounded off to the nearestthousandths. 3.At section 1 of a pipe system carrying water the velocity is 3.0 fps and the diameter is 2.0 ft. At section 2 thediameter is 3.0 ft. Find the discharge and velocity at section 2.
1. Solve the following and draw the figures Í. A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward direction. A differential mercury manometer connected to the inlet and throat gives a reading of 30 cm. Find the [Ans. 154.02 lit/s] ii. If in the problem 13, instead of water, oil of sp. gr. 0.8 is flowing through the venturimeter, determine the [Ans. 173.56 lit/s] III. The water is flowing through a pipe of diameter 30 cm. The pipe is inclined and a venturimeter is inserted in the pipe. The diameter of venturimeter at throat is 15 cm. The difference of pressure between the inlet and throat of the venturimeter is measured by a liquid of sp. gr. 0.8 in an inverted U-tube which gives a reading of 40 cm. The loss of head between the inlet and throat is 0.3 times the kinetic head of the pipe. [Ans. 22.64 lit./s] discharge. Take Ca = 0.98. rate of flow of oil in litres/s. Find the discharge.
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200 150 - 125 - Suction lines 100 - 90 - 3 65 - 2 50 Discharge lines 40 32E 25 E 15 20 200 400 600 800 1000 2000 4000 6000 8000 10000 10 100 Volume Flow Rate, Q (gal/min) 6 8 10 ++++ 15 20 25 30 40 +++++++++ ++++++++++++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 Volume Flow Rate, Q (m/h)
1.Find the diameter of a pipe of length 3000 m when the rate of flow of water through the pipe is 300 litres/s and the head lost due to friction is 5 m. Take the value of C = 50 in Chezy’s formula.
Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h1 = 0.3 m, compute the water flow from side nozzle of diameter (d = 10 mm) and the rise h₂ from that nozzle. vesn Air pressure It, 11₂ Nozzle
Water flows through a 125 mm diameter pipe at a velocity of 7.5 m/sec. Find the mass flow rate in kg/sec. NOTE: Do not write any unit to your answer, put your answer in a numerical form only and use up to 3 decimal places. ASAP PLS
a) Two pipes have a length ? each. One of them has a diameter D, and the other a diameter d.if the pipes are arranged in parallel, the loss of head when a total quantity of water Q flows through them is h, but, if the pipes are arranged in series and the same quantity Q flows through them, the loss of head is H. If ?=?/2, find the ratio of H to h, neglecting secondary losses and assuming the pipe coefficient f has a constant value. b) A pipeline of 0.6m diameter is 1.5km long.To increase the discharge, another line of the same diameter is introduced parallel to the first in the second half of the length.Neglecting minor losses, find the increase in discharge if 4f = 0.04. The head at inlet is 300mm. c) Determine the difference in the elevations between the water surfaces in the two tanks which are connected by a horizontal pipe of diameter 300 mm and a length of 400 mm. The rate of flow of water through the pipe is 300 litres/s. Consider all losses and takef=0.008. d) Water at 20°C is…
Solve and draw also the figures. i. Water is flowing through a pipe of 100 mm diameter under a pressure of 19.62 N/cm² (gauge) and with mean velocity of 3.0 m/s. Find the total head of the water at a cross-section, which is 8 m above the datum [Ans. 28.458 m] ii. A pipe, through which water is flowing is having diameters 40 cm and 20 cm at the cross-sections 1 and 2 respectively. The velocity of water at section 1 is given 5.0 m/s. Find the velocity head at the sections 1 [Ans. 1.274 m ; 20.387 m ; 0.628 m³/s] line. and 2 and also rate of discharge. The water is flowing through a pipe having diameters 20 cm and 15 cm at sections 1 and 2 respectively. iii. The rate of flow through pipe is 40 litres/s. The section 1 is 6 m above datum line and section 2 is 3 m above the datum. If the pressure at section 1 is 29.43 N/em², find the intensity of pressure at section 2. [Ans. 32.19 N/cm²]
find the volumetric flow ratewater is passing through a pipe with an inside diameter of 4 inches and a flow velocity of 56 feet per second. What is the GPM? Note: align the units of time, Length and 231 cubic inches equals one gallon of water.