5. Air entering at 70°F and atmospheric pressure is to be compressed to 4000 lb:/in² gauge in a reciprocating compressor at the rate of 125 std ft³ /min. How many stages should be used? What is the theoretical shaft work per standard cubic foot for frictionless adiabatc compression? What is the brake horsepower if the efficiency of each stage is 85 percent? For air y = 1.40.? What is the discharge temperature of the air from the first stage?

5. Air entering at 70°F and atmospheric pressure is to be compressed to 4000 lb:/in² gauge in a reciprocating compressor at the rate of 125 std ft³ /min. How many stages should be used? What is the theoretical shaft work per standard cubic foot for frictionless adiabatc compression? What is the brake horsepower if the efficiency of each stage is 85 percent? For air y = 1.40.? What is the discharge temperature of the air from the first stage?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) A single stage, single acting reciprocating compressor has a bore of 250 mm and a stroke of 550 mm. It runs at a speed of 300 rev/min. The clearance is 4% of swept volume, and the polytropic index is 1.39 throughout. The intake pressure is 97 kPa at 25°C, and the final compression pressure is 600 kPa. If the free air conditions are 101 kPa and 20°C, determine the free air delivered in m/s.
1) Discuss the difference in the velocities of the model and main pipe.
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)
When using a double acting pressure intensifier for continuous pressure increase, we are looking to have pressure intensified brand operate at 5L/min at 30 MPA. If the main pump can supply 10L/min at 10 MPA, what is the diameter ratio needed between actuator and boosting piston?
a) Calculate the interstage pressure ratio per stage for a two-stage compressor if the overall pressure ratio is 10. b) What speed should a single acting, reciprocating compressor run at to produce 50 m³/h of air? The data for the compressor is: Piston diameter = 100 mm, Stroke length = 110 mm,
3. At 200C and 98kPaa existing barometric pressure, fan develops a brake power of 95kW. If operates at 95kPaa and 320C with the same speed, what is the new break power of the fan? 4. An mixed flow centrifugal blower having a flow capacity of 4500cfm has a suction and discharge diameter of 24in and 20in respectively. The manometer reading at the suction and discharge line are measured to be 10in-Hg vacuum and 20in-Hg. If the existing barometric conditions are 14.3psia and 550F, determine the required horsepower of the blower motor if the rated efficiency of the fan is 89%.
A pitot tube is used to measure the flow rate of air at a temperature of 500 K inside a duct. If the measured static pressure was 200 kPa, the measured stagnation pressure was 223 kPa and the air can be treated as an ideal gas what is the air velocity?
Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor in kW to 2 decimal places if the compression is polytropic compression process with n=1.25?
Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal?
3.11) The conditions of air at the entry of an axial compressor stage are: Рi %3D 768 тт Hg & Ti = 314 K. The air angles are B1 = 51°, B2 = 9°, a1 = az = 7°. The mean diameter 50 ст. The peripheral speed 100 m/s. Mass-flow rate 25 kg/s work done factor 0.95 mechanical efficiency 92 % stage efficiency 88 % (a) Air angle at the stator entry, [a2 50.18°] (b) Blade height at entry and the hub-tip diameter ratio, [h, = 19 cm ; dn/d = 0.449] (c) Stage loading coefficient. [V = 0.754] (d) Stage pressure ratio. [Po3/Po1 1.075] (e) The power required to drive the stage. [Power = 204.75 kW]
QUESTION 1:A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300kW (shaft power) and rotates at 96.3 rad/s. The flow rate generated by the machine is54.7 Kilo-litres/min. The impeller blade inlet angle and width is 23° and 180 mmrespectively. The blades occupy 12% of the impeller area and the water is assumed toenter the impeller radially. Suction and delivery pipes are equal in size.Determine:1.1The impeller inlet (i) diameter and inlet blade velocity.(Hint - Substitution: ln in terms of D and U, in terms of D, both sub into Tan of Blade inlet angle,only unknown is then solving for Dz)1.2.If the pump has a mechanical efficiency of 80%, calculate the blade velocity atoutlet (U.) and outlet whirl velocity Vw.. Assume the blade exit angle equal to theguide vane angle. (Hint - Substitution: Write Vw in terms of U, sub in Euler equation onlyunknown then is solve for Vwo)1 3Impeller outer diameter.1.4,If the flow through velocity is consistent through the…
Draw the different cases for the inlet and outlet velocity triangle for centrifugal compressor. Also draw the velocity triangle centrifugal compressor with consideration of the slip. Give a numerical example.