4-54. The spool has a mass of 200 kg and rests against the wall and on the floor. If the coefficient of static friction at B is (4)e = 0.3, the coefficient of kinetic friction is (He)B = 0.2, and the wall is smooth, determine the friction force developed at B when the vertical force applied to the cable is P= 80 N. 0.4 m 0.1 m

4-54. The spool has a mass of 200 kg and rests against the wall and on the floor. If the coefficient of static friction at B is (4)e = 0.3, the coefficient of kinetic friction is (He)B = 0.2, and the wall is smooth, determine the friction force developed at B when the vertical force applied to the cable is P= 80 N. 0.4 m 0.1 m

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

6-23. The compound beam is subjected to a uniform dead load of 2 kN/m and a uniform live load of 1.5 kN/m. Determine (a) the maximum negative moment these loads B develop at A, and (b) the maximum positive shear at D. Assume B is a pin and C is a roller. 2 m 2 m 2 m
a 600 N block rests of a 30 degrees plane. if the coefficient of friction is 0.20 , what is the value of the force, P applied horizontally to keep the block moving up the plane
13-5. If blocks A and B of mass 10 kg and 6 kg respectively, are placed on the inclined plane and released, determine the force developed in the link. The coefficients of kinetic friction between the blocks and the inclined plane are HA = 0.1 and µg = 0.3. Neglect the mass of the link. 30°
3-6. The gusset plate is subjected to the forces of three members. Determine the tension force in member C and its angle for equilibrium. The forces are concurrent at point O. Take F = 8 kN. y TO De 9 kN A 1000 Cada 1000 900 10 C F T ·X
A block with a mass m = 10kg is sitting on an inclined plane witn an angle of 30 degrees. The block is connectec to a wall by a wire which has tension so that the block is stationary. The coefficient of static friction between the block and the plans is 0.2. Calculate tension
5-75. If the cable can be subjected to a maximum tension of 300 Ib, determine the maximum force F which may be applied to the plate. Compute the x, y, z components of reaction at the hinge A for this loading. 3 ft A 3R 9ft
A pair of wedges is used to lift a crate as shown in The crate weighs 4000 lb, the wedge angle e is Fig. 18°, and the coefficient of friction is 0.15 at all surfaces. The weight of the wedges is negligible. Determine The force P necessary to remove the wedge or to pre- vent the wedge from slipping out W
Problem A block of mass m is placed on a rough surface inclined relative to the horizontal. The incline angle is increased until the block start to move. Show that you can obtain the coefficient of static friction ug by measuring the critical angle 0 where slipping occurs. mg pino to .... my 18.
In downhill speed skiing a skier is retarded by both the air drag force on the body and the kinetic frictional force on the skis. (a) Suppose the slope angle is u =40.0, the snow is dry snow with a coefficient of kinetic friction mk =0.0400, the mass of the skier and equipment is m =85.0 kg, the cross-sectional area of the (tucked) skier is A = 1.30 m2, the drag coefficient is C =0.150, and the air density is 1.20 kg/m3. (a) What is the terminal speed? (b) If a skier can vary C by a slight amount dC by adjusting, say, the hand positions, what is the corresponding variation in the terminal speed?
A 500-kg block is resting on a 30 deg. inclined plane with a coefficient of friction of 0.3. Find the required force P acting horizontally that will start the block up the plane.
3-23. Determine the maximum weight W of the block that can be suspended in the position shown if each cord can support a maximum tension of 80 lb. Also, what is the angle 0 for equilibrium? 30 т
At what height in (A) must the wooden board be inclined such that the maximum static friction is obtained when the angle of repose is 32.4°?