300 mm -700 mm -125 mm 500 mm M A Q-3 Q-3: The coefficient of static friction between the drum and brake bar is s = 0.40. If the moment M = 48 Nm, determine the smallest force P that needs to be applied to the brake to prevent the drum from rotating. Also, determine the corresponding horizontal and vertical components of reaction at pin O. Neglect the weight and thickness of the brake bar. The drum has a mass of 30 kg.

300 mm -700 mm -125 mm 500 mm M A Q-3 Q-3: The coefficient of static friction between the drum and brake bar is s = 0.40. If the moment M = 48 Nm, determine the smallest force P that needs to be applied to the brake to prevent the drum from rotating. Also, determine the corresponding horizontal and vertical components of reaction at pin O. Neglect the weight and thickness of the brake bar. The drum has a mass of 30 kg.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter15: Oscillations

Section: Chapter Questions

Problem 40P: Reciprocating motion uses the rotation of a motor to produce linear motion up and down or back and...

See similar textbooks

Similar questions

A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
The temperature of the atmosphere oscillates from a maximum near noontime and a minimum near sunrise. Would you consider the atmosphere to be in stable or unstable equilibrium?
(a) When water freezes, its volume increases by 9.05% (that is, V/V0=9.05102 ). What force per unit area is water capable of exerting on a container when it freezes? (It is acceptable to use the bulk modulus of water in this problem.) (b) Is it surprising that such forces can fracture engine blocks, boulders, and the like?
Reciprocating motion uses the rotation of a motor to produce linear motion up and down or back and forth. This is how a reciprocating saw operates, as shown below. If the motor rotates at 60 Hz and has a radius of 3.0 cm,estimate the maximum speed of the saw blade as it moves up and down. This design is known as a scotch yoke.
Q2: A conveyor beam has the cross section shown below and it is subjected to a ben moment. Determine the maximum permissible bending moment which can be applie the heam when the hottom flange in tancion, if the safe atenen for the mate tension and compression are 30 MPa and 150 MPa respectively. T C VI 25 mm 150 mm 100 mm 50 mm المانه *50*100*50* mm mm mm
A pivot bearing used on the shaft of an electrical instrument is shown in the figure below. An oil with a viscosity of μ = 0.010 lb-s/ft² fills the 0.0013-in. gap between the rotating shaft and the stationary base. Determine the frictional torque on the shaft when it rotates at 6700 rpm. 0.0013in. 6700rpm 30° 0.2 in. -0.010 lbs/ft²
Data has been gathered from a lifting system used to trans port engine parts. The sys tem consis ts of a drum and cable. The following data was obtained when the drum lowers the load (assume cons tant acceleration). Drum diameter = 1m Mass of load - 9kg Initial velocity =0 m/s Time to des cend- 64 secs Distance travelled 0.7m You have been asked to use this information to determine: Cable a) The final linear velocity of the load b) The linear acceleration of the load Load c) The final angular velocity of the drum d) The angular acceleration of the drum e) The tension force in the cable f) The torque applied to the drum Fioure 1 solve (d),(e),(f) parts and please mention kinematic equations which need to solve this question
SF-1 A coil spring has an unloaded total length of 25.0cm. The spring constant is 1.20N/cm. The left end of the spring is attached to a rigid support (can't move). a) Draw the spring on your paper at its unloaded length. b) Below your first drawing, draw the spring with a length L-35.0cm and show the force F needed to hold the spring at this length. Calculate the magnitude of F. c) Below your second drawing, draw the spring with a length L-25.0cm and show the force F needed to hold the spring at this length. Calculate the magnitude of F. 25.0cm
A spring-mass system is shown in the following figure. Use m = 1.5 kg and k = 120 N/m. Equilibrium position m a) Determine the static deflection ôy. Insert your answer in meters correct up to at least a third decimal place. Sul b) Determine the system period t. Insert your answer in seconds correct up to at least a third decimal place. Sul c) Determine the maximum velocity Umax which result if the cylinder is displaced 135 mm downward from its equilib position and released from rest. Insert your answer in m/s correct up to at least a third decimal place.
Referring to Fig. compute the maximum force P that can be applied by the machine operator, If the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 4000 psi and 5000 psi, respectively. The diameters are 0.25 inch for the pin, and 0.5 inch for the control rod. Assume single shear for the pin at B. Figure P-121 2 in 10 MATHno.com 6 in 2 in
The figure shows a pneumatic system whose center opening is controlled by a 3-way valve. The perimeter of the ports is w. When the reel is at the center, x = 0. While solving the problem, you can make assumptions that you think are realistic and define the necessary parameters. Find an expression that gives the rate at which the load of weight W moves upward when X = Xo. Find an expression for the rate at which the load moves downward when X = -Xo.
Q2) A shaft rotating at 350 r.p.m. drives another shaft at 550 r.p.m. and transmits 10.5 kW through a belt. The belt is 80 mm wide and 9.5 mm thick. The distance between the shafts is 3.8 m. The smaller pulley is 9 cm in diameter. Calculate the stress in the belt, if it is an open belt drive, Take u = 0.3.2.. (30 degrees)