3. Water from an open reservoir A at 8m elevation is drawn by a motor-driven pump to an open reservoir B 70m elevation. The inside diameter of the suction. The inside diameter of the suction pipe is 200 mm and 150 mm for the discharge pipe. The suction line has a head loss 3 times that of the suction velocity head. The discharge line has a loss of head twenty times that of the velocity head of the discharge pipeline. The pump centreline is at 4m for a discharge rate of 10 Liters/sec. Find the Total Dynamic Head?

3. Water from an open reservoir A at 8m elevation is drawn by a motor-driven pump to an open reservoir B 70m elevation. The inside diameter of the suction. The inside diameter of the suction pipe is 200 mm and 150 mm for the discharge pipe. The suction line has a head loss 3 times that of the suction velocity head. The discharge line has a loss of head twenty times that of the velocity head of the discharge pipeline. The pump centreline is at 4m for a discharge rate of 10 Liters/sec. Find the Total Dynamic Head?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

times A cenrifugal pump having outer diameter equal two the inner diameter and running at 1200rpm works agaist a total head of 32m. The velocity of flow through the impeller is constant and equal to 3m/s. The vanes are set back at an anhgle of 30°at the outlet. If the outer diameter of the impeller is 600mm and width at outlet is 50mm, determine: a- Vane angle at inlet. b- Work done per second by impeller. c- Manometric efficiency.
The value of (NPSH) for a pump is given by the manufacturer as 10 ft. Water is being pumped from a reservoir at min atmospheric pressure at a rate of 30 ft /s to a tank at atmospheric pressure. The water level in the reservoir is 5 ft below the pump. If the total head loss in the suction pipe is 5 ft, is the pump safe from cavitation effects? If a 2-in schedule 40 pipe of 150 m length was used downstream of the pump, what is the power delivered to the fluid? You may assume that the friction factor in the pipe is equal to 0.004.
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The sucLon pipe is 350mm in diameter and 12m in length and the delivery pipe is 550mm in diameter and 40m in length. Calculate:(a) The maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa (gauge) (b) the energy to be supplied by the pump per unit mass of water transferred (c) The input power required by the pump, which is 60 % efficient
Aa certain hydro-power station has a head of 500m between the upper and lower reservior. A. Determing the approach velocity of water as it enters the turbine ; B. If the volume flowrate is 60cumec, what is the diameter of the penstock; and C. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity approach and the corrected diameter of the penstock required
3. A centrifugal pump is to be placed above a large, open water tank, as shown in the figure below. Water is pumped at a rate of I cu ft/s. At this flow rate the required net positive suction head, NPSHR, is 15 ft as specified by the pump manufacturer. The water temperature is 80°F and atmospheric pressure is 14.7 psi. Assume that the major head loss between the tank and the pump inlet is due to filter at the pipe inlet having a minor loss coefficient KL.-20. Other losses can be neglected. The pipe on the suction side of the pump has a diameter of 5 in. The water vapor pressure at 80°F is 0.5069 psia and y-62.22 lb/cu.ft. Determine Z1 for cavitation not to occur.. P1-Patm (1) (2) Reference plane
A certain hydro-power station has a head of 500m between the upper and lower reservoir . a. Determine the approach velocity of water as it enters the turbine; b. If the volume flow rate is 60 cumec, what is the diameter of the penstock; and c. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity of approach and the corrected diameter of the penstock required.
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)
An inward flow reaction turbine has external and internal diameters as 1.095 m and 0.553 m respectively. The turbine is running at 210 R. P. M. The velocity of flow through the runner remains constant and is equal to 2.0 m/s. The width of the turbine at inlet is 241 mm. The guide blades make an angle of 10.5oto the tangent of the wheel. If the discharge of the turbine at the outlet is radial determine the following:i) Draw the inlet and outlet velocity diagramsii) The absolute velocity of the water at the inlet of the runner.iii) The velocity of whirl at inletiv) The relative velocity at inletv) The runner blade anglesvi) Width of the runner at outletvii)The hydraulic efficiency of the turbine
B- Calculate the power required for a water pump used in a closed system with flow rate Q=0.0076 m³/s. Assume that section area=0.00511 m² and at the area at the discharge is 0.0037 m². As AJ Water Suction Discharge pump Inlet gauge pressure=147 kPa Outlet gauge pressure=250 kPa
a pumping station working with a pump head of 25m. the output power of the motor for that pump is 16kw. identify the pump efficiency if the sewarge discharge velocity is 0.27 m/s and the pipe diameter is 250 mm
C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The velocity at the smaller end is 4.9 m/s and at the larger end is 2.5 m/s. The length of the conical tube is 1.3 m and the flow rate of the water is 127 liters/s. The pressure at the smaller end is equivalent to a head of 10.1 m of water. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the diameter at the smaller end in meter, (ii) the diameter at the larger end in meter, and (ii) the pressure at the larger end of the tube in m of water. (2) If a head loss (with head loss)in the tube,h = 0.0153(V1-V2)2, where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of water and (v) the pressure at the larger end of the tube in m of water. 6) the diameter at the smaller end in meter (ii) the diameter at the larger end in meter (iii) the pressure head at the larger end of the…
A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?