3. The block has a weight of 35 lb and is being hoisted at uniform velocity. Suppose that 0= 48°.BAo Express the force along AD in vector =} Ibo Express the force along AC in vector =i} 1bo The resultant force vector (FA) of FAD and FACi} Ibo The magnitude of the resultant force FA =lbo The direction angle of the resultant force FA =° (measured in counter-clock-wise from +x axis)o Force along AB =Ibo Angle y=

Answered: Image /qna-images/answer/484e9601-db0a-4a0f-ab95-50f13b5d4ffd.jpg

3. Thế block has a weight of 35 lb and is being hoisted at uniform velocity. Suppose that 0 = 48°. B A F o Express the force along AD in vector = j} lb o Express the force along AC in vector = i} Ib • The resultant force vector (FA) of FAD and FAC= j} Ib o The magnitude of the resultant force FA lb o The direction angle of the resultant force F = * (measured in counter-clock-wise from o Force along AB = Ib o Angle y=

3. Thế block has a weight of 35 lb and is being hoisted at uniform velocity. Suppose that 0 = 48°. B A F o Express the force along AD in vector = j} lb o Express the force along AC in vector = i} Ib • The resultant force vector (FA) of FAD and FAC= j} Ib o The magnitude of the resultant force FA lb o The direction angle of the resultant force F = * (measured in counter-clock-wise from o Force along AB = Ib o Angle y=

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An equilateral triangular prism (SG = 2/3) is floating on water as shown. A side of the equilateral triangle is 40cm and the prism is 2m long into the paper. Solve the resultant hydrostatic force on AB. B A O 800N O 906N O 604N O 700N
ЗР L/6 1. From figure 1.1. Determine 10 the distance 'a' as a fraction of the beam's length 'L' for locating the roller support at C so that the internal moment at B is zero. * 2. A particle is subjected to vector forces A = (2lb)i + (-6lb)j + (10lb)k and B = (-6lb)i %3D + (-2lb)j + (2lb)k. What will be the resultant force? *
USING VIRTUAL WORK METHOD. CALCULATE THE FOLLOWING: Considering the fully restrained beam shown in Figure 2 where E = 200 GPa and I = 2x109 mm^4 Lo ‹-a L FIGURE 2 The beam is loaded as follows: • Concentrated moment at a point 5 m. from the left support • Load P inclined at angle G with respect to the horizontal, acting at 3 m. from the right support. The beam is supported as follows: • Fixed support at the left and right end. If P = 85 KN, M = 120 kNm, L= 14 m., and G = 30 degrees. • Determine the vertical reaction, horizontal reaction, and moment reaction at support A and C. • Determine the deflection and slope at point B. • Determine the maximum deflection of the beam. . If the maximum deflection is limited to 12 mm, determine the diameter of the circular beam required.
8. 3 The deflection profile y(x) is given by emb A horizontal beam of unit length under load w(x) satisfies the system: y" = M, M" = w(x), x = (0, 1). free もエ 12 Find which end is embedded and which end is free. Find the load w(x). y y(x) = x¹ log(x) - OR free 4 = WCX) 25 еть x4 +4x³ - 3x². еть face y(0) = 0 y" (0) = 0, y !!! (o y' (8) = 8 (0) ) =
Two cables AB and AC are acting on the pole with forces FAB=540N and FAC=560N with parameters defining the attachment points shown in the table. We want to write the vector FAB in cartesian vector form. Уг parameters value units 540 560 5.5 FAB FAC L 71 4/₁ 72 4/2 →→ FAB= 281.88 3.5 Submit Question 4 N N m m m m m FAC A write the vector FAB in Cartensian Vector Notation. Round your final answers to 3 significant figures. xi +247.10 Y₁ Z AB B +-388.26 x N
1. Figure Q1 shows a simplified diagram of a Ram Air Turbine (RAT), where the force on the rotor is represented by the 2 kN load shown. a. Produce shear and moment diagrams for the supporting frame ABC. b. Calculate the horizontal deflection of the point of loading. Assume that frame ABC has bending stiffness El = 2.7×105 Nm². 0.9 m A 0.6 m C B 2 KN
Using Virtual work equation, determine the angle a° so that the deflection of the point C is in the same direction as the load P (Consider only EI the effects of bending due to the load P). Note: A direction of loading such that the resulting deflection is in the same L EI direction as the load is called a principal direction. For a given load on a planar structure, there are two principal directions, perpendicular to each other. L
A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2 m 1.2 m 1.2 m 2.8 m |F, = 6 kN y 45° |F,| = 5 kN %3D Using the coordinate system shown, determine the components of vector F2 = Fxi + F,J + F,k (Answer in Kilo Newtons) Choose... + Fy Choose... F2 Choose...
Determine the intenal normal force, shear force, and moment at point Cin the simply supported beam. Point Cis located just to the right of the 250 Nm couple moment. * Make sure to add units out of ** Your answer should look like this: Ne =, Vc=. Mc 100 N 5 m 300 N/m A 35 250 N.m 8 m 4 m 4 m 40 N Answer
NEED ANSWER ASAP!! The 16 x 22 x 25 mm rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 313 N causes the upper frame to be deflected downward by 4 mm. Determine the shear modulus G of the rubber blocks.
For the force system shown, a fifth force F must be added so that the resultant of the five forces will be a 450 N force directed from B to D. (a) What is the magnitude of the fifth force F? (b) What is the direction of the fifth force F? (c) Locate the point of intersection of the fifth force F and the line ABC. 90 N 220 N B 180 N A 220 N 100 mm 100 mm
Problem 1: Consider the beam shown below. It has a length 3L and is attached to a pin support and roller support at x = 0 and x= 3L, respectively. Its extremities are subjected to concentrated force Po and distributed load wo, respectively. Using the graphical method, draw the load w(x), shear V(x), and moment M(x) diagrams. Properly justify each step. A + 0 Po B U 2L Wo 3L X