Please answer in typing format 2. The operational amplifier is as shown below:A=10,000 R=10MQR-100OwwwR0%Rwww.Apa(a) Calculate v.. with an operational amplifier asshown in the triangular shape.20 k≤2wwwb6 V2 V40 k≤2www(b) Calculate the Thevenin's equivalent resistanceRT of the circuit in part (a).

Sure, I can help you analyze the circuit in the image. The circuit appears to be an inverting…

Answered: 2. The operational amplifier is as…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Graphically show the output voltage (Vo) and load current (IL) by simulating the difference receiving Op-Amp circuit given in the figure.(PSIM using PSpice or)R1 = R2=10kΩRL=1.5 kΩRf=14kΩ
2. The amplifier in the figure has a resistive input and is fed with a sine wave AC signal with peak voltage v,peak= 0.5 V, and peak current i,„peak= 0.02 mA. The resulting output voltage has a RMS value v,-RMS = 4 V rms- Find the following: a) The input resistance of the amplifier b) The output power c) The supply power V, +10V d) Amplifier dissipation. Assume input AC power is negligible e) Amplifier efficiency · 10 mA Vo i, R. 10 mA 100 2 Vi V,' -10V +1
In a summing inverting amplifier,Rf is 100k ohms, V1 is a sinusoid with 2V amplitude and frequency of 1Hz ,R1 is 10k ohms, V2 is a sinusoid with 3V amplitude and frequency of 1Hz, and R2 is 10k ohms. Vs+ = 18 V and Vs- = ground. What is the output voltage? Please draw the waveform as well.
Given a range of values for vs and v0, how are these calculated for v0 and how is the range for vs made to avoid op-amp saturation if it is -2 V < vs < 3 V? vs(v) 0.4 2.0 3.5 -0.6 -1.6 -2.4 vo(v) -2 -10 -15 3 8 10
3. A generic op-amp circuit is shown in Figure 3. With the given data, answer the following by showing the corresponding circuit and by explaining your answer or presenting the solution. a. If VA-0, VB-1V, RA-RB-10kQ, R1=70kQ, R2=00 and vout-8V, which terminal (A or B) is the noninverting input? b. If VA-10, VB=0V and B is the inverting input, select RA, RB, R1, and R2 and to obtain an output voltage of 20V. c. If VA=VB=1V, R1=0, R2=∞ and Vout=1V, which terminal (A or B) is the inverting input? R2 VA RA OVout RB B VB R1
a) Design an inverting operational amplifier that has an adjustable voltage gain between v = -10 and v = ở using a 100 k potentiometer Ra and another resistor Re. Determine RE. %3D b) Repeat part a) for a voltage gain between v = -10 and v = -1. A suitable resistor Rz in series to the potentiometer is required so that the gain cannot go to zero. Find Rz and RE.
4- For an operational amplifier circuit below. Draw the input and output waveforms if Vin is sine wave with 10 mV,R₁ = 10 KM, and R₂ = 100 KM. VI R₂ www PO
What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.
R, V OUT Let currents and node voltage for the Op-Amp circuit be defined as follows: |1 equals the current flowing through Rin from left to right. Let Vb be the voltage at the inverting input (-). Write 1 in terms of the node voltages Vin, Vb (voltage at inverting input). O Vb - Vin O Vvin - Vb O (Vb - Vin)/Rin O Vin - Vb) / Rin O - Vin/Rin
From the figure , write note voltage equations, one for each input terminal of the op amp The expression for the load current ( iL) can be written as a function of the input voltage (Vin) and the load voltage (VL) IL =A(Vin) + B(VL) b.1 What is the expression for A? b.2 What should be the condition for R1 R2 R3 R4 so that B is zero? (NB this will make( iL) depend only on Vin and not on RL)
Create Op-amp circuit... with:Vin= -1 Volt (DC) Vout = 14 Volt (DC) Only resistors with 1k, 3k, 5k, 7k and 11k ohms can be used while the circuit is being built. The V+ value of the LM741 IC to be used for op-amps will be 20 volts and the V- value will be -20 volts. You need to use at least one inverting amplifier and one non-inverting amplifier to build the circuit. Question: Write the gain formula of the circuit and calculate it, and write how we should find the Vout value..
Determine the output signal for the op-amp circuit shown in figure below, given Rf1 = 10 km, Rf2 = 5 ΚΩ, R = 1 ΚΩ. . R₁12 R41 #.. www V01 V₁-W V₂ w R Vov 02

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

2. The operational amplifier is as shown below: A=10,000 R=10MQ R-100 O www R 0% R www. Apa (a) Calculate v.. with an operational amplifier as shown in the triangular shape. 20 k≤2 www b 6 V 2 V 40 k≤2 www (b) Calculate the Thevenin's equivalent resistance RT of the circuit in part (a).