2. Shunt regulator of Figure uses a Zener whose voltage is 5.1V at a current of 10mA, and rz-892. The diode is fed from a supply V-15V (nominal voltage) and R=0.5KQ a) Calculate Vzo. Find Vo with no load and V' at its nominal value. b) Find the change in Vo resulting from a ±1V change in V". c) Find the change in Vo resulting from connecting a load resistance R₁ that draws a current I₁=ImA. d) Find Vo when RL-0.2KQ. Is the Zener still operating in the breakdown region?

2. Shunt regulator of Figure uses a Zener whose voltage is 5.1V at a current of 10mA, and rz-892. The diode is fed from a supply V-15V (nominal voltage) and R=0.5KQ a) Calculate Vzo. Find Vo with no load and V' at its nominal value. b) Find the change in Vo resulting from a ±1V change in V". c) Find the change in Vo resulting from connecting a load resistance R₁ that draws a current I₁=ImA. d) Find Vo when RL-0.2KQ. Is the Zener still operating in the breakdown region?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The Pinch off voltage for N-Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current, a. 4 mA b. 2.5 mA c. 2 mA d. 18 mA
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
Draw the waveform of the given clipper circuit and determine the following: a.) At 0V, what is the output voltage?b.) At +20V, what is the output voltage?c.) At -5V, what is the output voltage?
Design the power supply using diode components. This power supply sholud have 2 outputs. 12Vdc and 5Vdc. Input 240 Vac Supply i. Draw the circuit diagram ii. Bill of material/components that will be used iii. Teh output waveform for each stage
The positive peak value of output waveform for the given circuit diagram is.. . (VPP of input is 14 V, Bias voltage is 4 V, Diode is silicon) R1 I D, VIN VOut VELAS E
The Pinch off voltage for N-Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current.
For the circuit given in figure below draw the collector characteristic curves for Ip= 50, 150 and 250 micro amperes on the same graph Re 220 A - Vec 10 V R 10 k Boc= 200 OV-5 V
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
A fixed bias n-channel JFET with Vdd= 12V, Rd= 1.2k ohms. Idss=12mA and Vp=-4V. Determine Vs. a.0 V b.None of these c.4.35V d.6.7V
The DC value of a full-wave rectified voltage with a peak value of 55 V is a.) in bridge-type b.) in center-tapped