2. Find the support reactions at D and the tensionforces in AC and AB. The beam has a mass of100 kg per metre lengthof the longitudinallength of the beam.В2 m2 m3 m1 mA5 m2 m Find all the support reactions A and N and alsocalculate all the internal forces in the truss andstate whether in tension or compression. Useeither the method of joints or sections.Consider JY = YN = NJ, LO = ON = NL = JP = PL =%3D%3DLJ = GQ = QJ = JG and OL // JY //GX.UVWYTRSRPNMВ СDEF G HJKL100 kN 100 kN

As their are two questions, the first one is solved. Calculating the horizontal and vertical…

Answered: 2. Find the support reactions at D and…

2. Find the support reactions at D and the tension forces in AC and AB. The beam has a mass of 100 kg per metre lengthof the longitudinal length of the beam. B 2 m 2 m |C 3 m D 1 m A 5 m 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the bending stress at point B located at I m from the right end of the beam. 2 N/m 1N.m 2 cm 10 N I cm 0.6m 0.4m * Im Im
Calculate the vertical reaction at B in kN for the loaded truss as shown in the figure. Assume the area of all members as the same.
The truss structure in the figure is supported by a roller at Land hinge at M. When Fo= 65 kN. (a) list zero force members, (b)determine reactive forces at Land M, and (c) find member forces in BV, EV and EU, and VT, and state if they are in tension or compression. -5 @ 3m= 15 m- C JOK 01010 I L -4@4m=16m- B A D G Fo E 60 kN U S Q 0 T R P N M Fo
The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm? and 18 mm², respectively. Determine the force in bar CD in kN. ... D d 4kN/m A 5m ----
A simply supported beam is loaded as in figure. The bending moment at C is 4 KN 4 kN-m A 2m с 2m- 4 kN-m B
B -1→→+1 60° L-FL→ G F с D 50 KN 50 kN E 50 kN For the truss shown in the above figure, the force in member AC is
The frame ABCD consists of a rigid beam AC that is supported by two steel columns AB and CD with a modulus of elasticiyt of E = 17800 ksi. The rigid beam AC is orginally horizontal but after applying a concentrated force P = 5 kips, the beams tilts due to the difference in the area and the length of the supporting columns. [AAB = 1.4 in2, ACD = 1 in2, LA = 6 ft, LC = 4 ft, a = 1 ft, b = 2 ft and E= 17800 ksi] Determine the deformation in column CD? Determine the deformation in column AB? Determine the angle of rotation in rigid bar AC?inch
Problem 2 For the compound beam ABCDE shown below, determine the reactions at the supports A and E. Show necessary Free body diagrams. -6 m 800 N B 6 m- Hinge D -3 m 3 m E
GIVEN : The truss shown on the left 10 REQUIRED : a) Find reactions e supports 2000k- b) Calaulale the magnituck « nature of forces in members G. :D- AC, CD, DI , FG, ĠH, HI 10 So0ok. I 10 A
PROBLEM NO. 2. A rigid bar AD is supported by the pin-connected rod BC. A uniform distributed load 4 kN/m is applied along the top of rigid bar AD. Rod BC is made of A-36 steel and has a diameter of 50 mm. Two types of pins are connected at point A and point B, respectively. (a) Calculate and sketch the internal normal forces of rigid bar AD and rod BC (b) Calculate the support reactions and sketch the free body diagram. (c) Determine the minimum diameter of the pin at point A. (d) Determine the minimum diameter of the pin at point B. (e) Determine the elastic elongation of rod BC. Diameter of BC is 50 mm Allowable shear stress tallow of Pin A is 70 MPa, while tallow Of Pin B is 50MPA. 4 kN/m 3m |D |B 4m 4m Pin A Pin B
Q2 For the frame shown below use the Force Method to find the reactions and draw AFD, SFD and BMD. Assume that the flexural rigidity, El, of beam BC is three times as big as the one of beams AB and DC. 3 m 3 m 10 kN B H EI A 3 kN/m 3EI 8 m ΕΙ D 4 m
Problem 01 The figure shows a truss which is pin connected at C and supported by a roller at D. It carries a vertical loads of 200 kN and 100 kN at joints A and E respectively. State if it is tensile or compressive. 4m D 2m A. E 200 kN 100 kN 6m 3m OCalculate the force in member DE. 2Calculate the force in member BE. 3 Calculate the force in member BC.