A uniform rod whose mass equals 15.3 kg is supported by cable and hinge as shown below. The rod has a length of 2.5-m and supports a load of 300-Newtons. a. Draw free body diagram for the rod; b. Determine the tension in the cable. c. Determine the reaction forces at the hinge (R. and Ry ). 0 135 300-N 2.5 m 1.2 m

A uniform rod whose mass equals 15.3 kg is supported by cable and hinge as shown below. The rod has a length of 2.5-m and supports a load of 300-Newtons. a. Draw free body diagram for the rod; b. Determine the tension in the cable. c. Determine the reaction forces at the hinge (R. and Ry ). 0 135 300-N 2.5 m 1.2 m

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section8.3: Equilibrium

Problem 40PP

See similar textbooks

Similar questions

Suppose a 900-kg car is on the bridge in Figure 9.34 with its center of mass halfway between the hinges and the cable attachments. (The bridge is supported by the cables and hinges only.) (a) Find the force in the cables. (b) Find the direction and magnitude of the force exerted by the hinges on the bridge.
A sandwich board advertising sign is constructed as shown in Figure 9.35. The sign's mass is 8.00 kg. (a) Calculate the tension in the chain assuming no friction between the legs and the sidewalk. (b) What force is exerted by each side on the hinge?
a) What is the mechanical advantage of a wheelbarrow, such as the one in Figure 9.24, if the center of gravity of the wheelbarrow and its load has a perpendicular lever arm of 5.50 cm, while the hands have a perpendicular lever arm of 1.02 m? (b) What upward force should you exert to support the wheelbarrow and its load if their combined mass is 55.0 kg? (c) What force does the wheel exert on the ground? Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
The upper leg muscle (quadriceps) exerts a force of 1250 N, which is carried by a tendon over the kneecap (the patella) at the angles shown in Figure 9.38. Find the direction and magnitude of the force exerted by the kneecap on the upper leg bone (the femur). Figure 9.38 The knee joint works like a hinge to bend and straighten the lower leg. It permits a person to sit, stand, and pivot.
The forearm shown below is positioned at an angle with respect to the upper arm , and a 5.0- kg mass is held in the hand. The total mass of the forearm and hand is 3.0 kg, and their center of mass is 15.0 cm from the elbow. (a) What is the magnitude of the force that the biceps muscle exerts on the forearm for =60 ? (b) What is the magnitude of the force on the elbow joint for the same angle? (c) How do these forces depend on the angle ?
In the What If? section of Example 12.2, let d represent the distance in meters between the person and the hinge at the left end of the beam. (a) Show that the cable tension is given by T = 93.9d + 125, with T in newtons. (b) Show that the direction angle of the hinge force is described by tan=(323d+41)tan53.0 (c) Show that the magnitude of the hinge force is given by R=8.82103d29.65104d+4.96105 (d) Describe how the changes in T, , and R as d increases differ from one another.
Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
2. A 400-N weight is supported by a uniform beam with a mass of 30-kg and a length of 1.6 meters. The beam is connected to a wall through a hinged connection at point C as shown below. If the system is in static equilibrium, draw a free-body diagram and determine; a. The applied tension. b. The reaction forces at the hinge (R, and Ry). 400 N Wbeam 1.6 m √60° 0.8 m 1.2 m
2. A 400-N weight is supported by a uniform beam with a mass of 30-kg and a length of 1.6 meters. The beam is connected to a wall through a hinged connection at point C as shown below. If the system is in static equilibrium, draw a free-body diagram and determine; a. The applied tension. b. The reaction forces at the hinge (R. and Ry). 400 N W beam 1.6 m 60° 0.8 m 1.2 m C
3. In the figure shown, a = 12.00 cm, b = 5.00 cm, and W = 120 N. If the horizontal bar is uniform and weighs 50 N, A. Draw the FBD and show all the forces acting on the bar. B. Determine the tension experienced by the cable. C. Determine the horizontal and vertical components of the reaction at the hinge. b C a W
3. A bridge is 36.5 m long and weighs 2.56 x 10 N. A truck weighing 5.25 x 10* N is 10.2 m from one end of the bridge. Calculate the upward force that must be exerted by each pier to support this weight. 10.2 m Wright 4. (Phy235) A bar 5.0 m long has its center of gravity 1.5 m from the heavy end. If it is placed on the edge of a block 1.5 m from the light end and a weight of 750 N is placed on the bar, it is balanced. What is the weight of the bar?
Name: ID: A 19. A uniform 120-lb beam is supported in a horizontal position by a pin and cable as shown in the figure. What is the magnitude of the force by the pin on the beam? 37 12 ft a. 94 lb b. 88 lb 63 lb d. 75 lb 150 Ib C. c.