(2) Set the wavelength of the spectrophotometer to 400 nm. . Place the stock solution (Solution 5) in a cuvet following the "blank solution procedure" as above. Measure and record the wavelength and absorbance. Scan the wavelength range of the spectrophotometer while recording absorbance values. You will need to scan manually, setting the absorbance at zero (100% T) with the blank solution (0.1 M HNO3) at EACH chosen wavelength before recording the absorbance of the stock solution. Plot the data, absorbance, A (y-axis) versus the wavelength, à (x-axis), to determine the Amax, the wavelength where maximum absorbance occurs for the cobalt ion. Absorbance 0.6 0.5 0.4 0.3 0.2 0.1 0.0 500% 600 Wavelength (nm) A representative absorption spectrum of a laboratory solution. 148 300 400 700 800

(2) Set the wavelength of the spectrophotometer to 400 nm. . Place the stock solution (Solution 5) in a cuvet following the "blank solution procedure" as above. Measure and record the wavelength and absorbance. Scan the wavelength range of the spectrophotometer while recording absorbance values. You will need to scan manually, setting the absorbance at zero (100% T) with the blank solution (0.1 M HNO3) at EACH chosen wavelength before recording the absorbance of the stock solution. Plot the data, absorbance, A (y-axis) versus the wavelength, à (x-axis), to determine the Amax, the wavelength where maximum absorbance occurs for the cobalt ion. Absorbance 0.6 0.5 0.4 0.3 0.2 0.1 0.0 500% 600 Wavelength (nm) A representative absorption spectrum of a laboratory solution. 148 300 400 700 800

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter4: Least-squares And Calibration Methods

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

what is the difference of spectrophotometer with ATR (attenuated total reflectance) and one without it. What are the advantages of one over the other?
fill in the column thats empty by finding the standard deviation for each average absorbance, with work please.
uestion 5 of 24 Identify the components in the single-beam spectrophotometer schematic. Then, match the spectrophotometer component with its description. Each component will be used once when labeling the diagram and once when matching to the description. P Po 0. Answer Bank detector light source monochromator sample cuvet It holds the sample and has a defined pathlength. It provides electromagnetic radiation in the ultraviolet (UV), visible, or infrared (IR) region of the spectrum. It is typically a grating, prism, or filter that selects a narrow wavelength band of radiation and passes it to the sample. It is typically a photomultiplier tube that generates an electric signal when struck by photons.
cont irmation True or false: The purpose of the internal standard is to make quantitation of the analyte insensitive to injection errors
An HPLC setup has an injection volume of 0.353 mL and a detector volume of 0.300 mL. The baseline width, Wobs, of a band eluting from the column at a flow rate of 1.45 ml/min is observed to be 35.6 s. Calculate the baseline width of the band, in seconds, if the column was the only source of broadening. Wcolumn= S
Label the graph with the correct axes for a standard curve used in a spectrophotometry experiment. y X Answer Bank Concentration (M) % Transmittance Sample # Absorbance Density (g/L)
In UV and visible spectrophotometry, the specimen is generally dissolved in a solvent, and determinations are made at room temperature using a path length of 1 cm. Give the most common solvents suitable for UV or visible spectrophotometry.
Column Plate Number: 16Retention Factor: 3.1Sample Peak Retention Time: 1.2minutesSample Peak Width: 1.53First Peak Retention Factor: 2.10Second Peak Retention Factor: 1.37Efficiency: 0.43Pressure: 375barrColumn: 28cm x 5mmViscosity: 2.3poiseFlow Rate: 1.2Column Permeability: 2.8 FIND: a & ba. Resolution b. Pressure if flow rate is adjusted to 2.3 c. Particle Size d. Selectivity Factor e. The retention time of the unretained peak
What is the purpose of reference beam in the double-beam spectrophotometer shown in Figure 20-1? Select all the correct answers. a)To correct for changes in source light intensity as a function of time b)to correct for changes in intensity of the light source as a function of wavelength c)to correct of scattering of light off the surface of the sample cuvette d)to correct for absorbance of the solvent e)to correct for changes in detector signal as a function of wavelength
Q4) (a) Explain how the components of a mixture are separated in gas chromatography. (b) An aqueous solution whose concentration is 0.00356 M was analyzed using spectrophotometer with a molar absorptivity of 412 cm-1 mol-1 L in a cell with a 2.00 cm pathlength. Calculate the absorbance and transmittance for the above solution. (c) Analyze the reasons why a dropping mercury electrode is better as compared to a conventional electrode.
What are the 5 important characteristics of spectrophotometric methods
In the analysis conducted with flame AAS, standard solutions of the X-type are analyzed individually and the absorbance values obtained are plotted against concentration (ppm). It was seen that the slope of the calibration line obtained was 0.0925. The standard deviation of the absorbance values obtained by reading the blank 10 times under the same conditions was calculated as 0.00183 ppm. According to this; For the X-type calculate the following: a) LOD b) LOQ c) Sensitivity