2 pointsThe input voltage and current of ac circuit depicted in Figure are v(t) = Vm sin(wt +0v), i(t) = Im sin(wt + 8;). The average power delivered to the circuit is P Watt, where Vm= 62 V, Im = 3A, 8v=-100, P = 54W.Find the angle 8; in degree that corresponds to the mentioned delivered power.A Moving to the next question prevents changes to this answer.PLoadQuestion 4 of 7 >

Answered: Image /qna-images/answer/47da6020-85a3-47a7-9b4b-ab9f59f63743.jpg

2 points The input voltage and current of ac circuit depicted in Figure are v(t) = Vm sin(wt + 8y), i(t) = Im sin(wt + 8;). The average power delivered to the circuit is P Watt, where Vm = 62 V. Im = 3A, 0y=-100, P= 54 W. Find the angle 8; in degree that corresponds to the mentioned delivered power. D V Load

2 points The input voltage and current of ac circuit depicted in Figure are v(t) = Vm sin(wt + 8y), i(t) = Im sin(wt + 8;). The average power delivered to the circuit is P Watt, where Vm = 62 V. Im = 3A, 0y=-100, P= 54 W. Find the angle 8; in degree that corresponds to the mentioned delivered power. D V Load

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot
Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100mH : 15 2 Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and / and state the relationship between Vs and I. (ii) (iv) Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load.
(a) A very important parameter in AC power circuits is power factor. Justify this phrase. Then, explain the difference between leading and lagging power factor. Describe the phase relationship between voltage and current for these two conditions to support your answer.
1 Calculate average and RMS value of the voltage waveform given in Figure. 4V %3D t(ms)- 4V
Calculate the apparent power, real power, andreactive power for the circuit shown in Figure.Draw the power triangle. Assume a.) f = 50 Hz. b.) f = 0 Hz (DC)
Find the RMS value of V)-100 sin(377t+76) V
b. Q = -3KVAR ,P = 5kW Determine the Complex Power, Apparent Power, Current, Voltage and Power factor and state if it is lagging or leading. Draw the current and voltage phasor diagram and the power triangle.
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002
A single phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?
The voltage and current of an ac circuit are as follows:e = 141. sin (377t + 10) V and i = 10 cos (377t-30)A. Find the power factor. Select the correct response: 0.46 leading 0.46 lagging 0.64 lagging 0.64 leading Continue > < Previous 3 n.ub.edu.ph/student_take_quiz_assignment/start/33008469#
An AC supply voltage is represented by v = 325 Sin wt. Three loads are connected in parallel across the supply, and the currents through these loads respectively are: 1=8.48 Sin wt 12 = 4.24 Sin (wt - 15°) 3 = 6.36 Sin (wt + 90°) Which of the following is the supply current? O a. 13.49 75°A O b. 9.63222.65°A O c. 19.08275°4 O d. 7.49275 A