10. A mass is vibrating at the end of a spring of force constant 250 N/m. The figure below shows a graph of its position x as a function of time t. x (cm) 5 -5 2 4 6 00 t(s) a) Rank the "times (1 s, 3 s, 5 s, 7s) at which the speeds from the lowest to the highest? b) How much energy did this system contain at t=4s? c) How much energy did the system lose between t₁ = 2.0 s and t₂ = 8.0 s?

Integrated Concepts A toy gun uses a spring with a force constant of 300 N/m to propel a 10.0-g steel ball. If the spring is compressed 7.00 cm and friction is negligible: (a) How much force is needed to compress the spring? (b) To what maximum height can the ball be shot? (c) At what angles above the horizontal may a child aim to hit a target 3.00 m away at the same height as the gun? (d) What is the gun's maximum range on level ground?

Review. A 0.250-kg block resting on a frictionless, horizontal surface is attached to a spring whose force constant is 83.8 N/m as in Figure P15.15. A horizontal force F causes the spring to stretch a distance of 5.46 cm from its equilibrium position. (a) Find the magnitude of F. (b) What is the total energy stored in the system when the spring is stretched? (c) Find the magnitude of the acceleration of the block just after the applied force is removed. (d) Find the speed of the block when it first reaches the equilibrium position. (e) If the surface is not frictionless but the block still reaches the equilibrium position, would your answer to part (d) be larger or smaller? (f) What other information would you need to know to find the actual answer to part (d) in this case? (g) What is the largest value of the coefficient of friction that would allow the block to reach the equilibrium position? Figure P15.15

An automobile having a mass of 1.00 103 kg is driven into a brick wall in a safety test. The bumper behaves like a spring with constant 5.00 105 N/m and is compressed 3.16 cm as the car is brought to rest. What was the speed of the car before impact, assuming no energy is lost in the collision with the wall?

An archer pulls her bowstring back 0.400 m by exerting a force that increases uniformly from zero to 230 N. (a) What is the equivalent spring constant of the bow? (b) How much work is done in pulling the bow?

A horizontal spring attached to a wall has a force constant of 850 N/m. A block of mass 1.00 kg is attached to the spring and oscillates freely on a horizontal, frictionless surface as in Figure 5.22. The initial goal of this problem is to find the velocity at the equilibrium point after the block is released. (a) What objects constitute the system, and through what forces do they interact? (b) What are the two points of interest? (c) Find the energy stored in the spring when the mass is stretched 6.00 cm from equilibrium and again when the mass passes through equilibrium after being released from rest. (d) Write the conservation of energy equation for this situation and solve it for the speed of the mass as it passes equilibrium. Substitute to obtain a numerical value. (e) What is the speed at the halfway point? Why isnt it half the speed at equilibrium?

One type of BB gun uses a spring-driven plunger to blow the BB from its barrel. (a) Calculate the force constant of its plunger’s spring if you must compress it 0.150 m to drive the 0.0500-kg plunger to a top speed of 20.0 m/s. (b) What force must be exerted to compress the spring?

A 0.250-kg block along a horizontal track has a speed of 1.50 m/s immediately before colliding with a light spring of force constant 4.60 N/m located at the end of the track. (a) What is the springs maximum compression if the track is frictionless? (b) If the track is not frictionless, would the springs maximum compression be greater than, less than, or equal to the value obtained in part (a)?

A cafeteria tray dispenser supports a stack of trays on a shelf that hangs from four identical spiral springs under tension, one near each corner of the shelf. Each tray is rectangular, 45.3 cm by 35.6 cm. 0.450 cm thick, and with mass 580 g. (a) Demonstrate that the top tray in the stack can always be at the same height above the floor, however many trays are in the dispenser, (b) Find the spring constant each spring should have for the dispenser to function in this convenient way. (c) Is any piece of data unnecessary for this determination?

An automobile having a mass of 1.00 103 kg is driven into a brick wall in a safety test. The bumper behaves like a spring with constant 5.00 105 N/m and is compressed 3.16 cm as the car is brought to rest. What was the speed of the car before impact, assuming no energy is lost in the collision with the wall?