1. The signal powerleaving a generatoris 3 dBm. It is connectedto an amplifier by a cable 4 ft. long. The attenuation/foot of the cable is 0.2 dB/ft. the gain of the amplifieris 30 dB. What is the output power?2. Given:IL = 1dBPin = 10dBmPix.Pout100cableWhat is the output power in dBm?3. Giventhemultistage cascaded amplifier system below. What is the output powerin dBm?0.3 ft1ft5 ft>A A> APoutPin20 dB15 dB10 dBAttenuation/footPin =- 5dBm=1dB

We need to find out output power for given amplifier

1. The signal power leaving a generator is 3 dBm. It is connectedto an amplifier by a cable 4 ft. long. The attenuation/ foot of the cable is 0.2 dB/ft. the gain of the amplifieris 30 dB. What is the output power? 2. Given: IL = 1 B Pout Pin = 10dBm Pa 100 cable What is the output power in dBm? 3. Giventhemultistage cascaded amplifier system below. What is the output powerin dBm? 1ft >A A> A 0.3 ft 5 ft Pout Pin 20 dB 15 dB 10 dB Pin =- 5dBm Attenuatiaoot =1dB

1. The signal power leaving a generator is 3 dBm. It is connectedto an amplifier by a cable 4 ft. long. The attenuation/ foot of the cable is 0.2 dB/ft. the gain of the amplifieris 30 dB. What is the output power? 2. Given: IL = 1 B Pout Pin = 10dBm Pa 100 cable What is the output power in dBm? 3. Giventhemultistage cascaded amplifier system below. What is the output powerin dBm? 1ft >A A> A 0.3 ft 5 ft Pout Pin 20 dB 15 dB 10 dB Pin =- 5dBm Attenuatiaoot =1dB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

what is rms value of below signallll.
11. What is the configuration of the given amplifier circuit below?12. How are the coupling capacitors treated in the figure of #11 at AC?
McqThe RMS current via the SCRS of the Bidirectional ac chopper is ................- of the RMS output current 0.5 0.775 1 0.707
Determine the output voltage value of a transistor amplifier circuit by frequency for 1.923 V to input voltage. Instead of. Calculate the gain in dB for the frequency given in the table. Maximum write down the frequency (s) where the gain is halved in terms of power (3dB). Frequency curve draw as
12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
Consider a step down converter supplied by a DC power source of magnitude Vs = 220 V. The switching period is 0.1 ms and the duty cycle k is set to 0.5. The load is an inductive load with R-S Ohms and L-10 mH. The switch is ideal. The RMS converter current IR is equal to 15.56A. The ripple factor of the input current RFs would be equal to: Select one: O a. None of these O b. 0% OC. 100% O d. 50%
At two distinct places, a signal is measured. At the first point, the power is P1, and at the second point, it is P2. The decibel level is zero. This denotes
Can we obtain a plot of XL against frequency f experimentally?
1. If we add a Zero into a system: I. The gain slop will be increased by 20db/decade at its corner frequency. II. The gain slop will be decreased by 20db/decade at its corner frequency. III. Gain will not be affected. IV. None of the above. 2. If we add a Pole into a system: I. The phase will be increased by 90 degrees. II. The phase will decrease by 90 degrees. III. Phase will not be affected. IV. None of the above. 3. In systems, the Integrator add slop to the system gain equal to: I. 20 db/decade. II. -20 db/decade. III. 0 db/decade. IV. None of the above 4. The purpose of the Lag Compensator is: I. Improve the study state response of the close system. II. Speed up the transit response. III. All the above. IV. None of the above. 5. In the Lead Compensator: I. Z > P. II. Z < P. III. Z = P. IV. None of the above.
i) Which type of compensator is used for feeding reactive power at the receiving end? Draw its block diagram. (ii) What is lag-lead compensator? Draw its circuit diagram and derive the expression for the transfer function of lag-lead compensator.
Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is an inductive load with R=10 Ohms and L-10 mH. The switch is ideal. The average source current is 4A. The ripple factor of the input current RFs is equal to: Select one: O a. None of these O b. 0% C. 100% d. 50% Clear my choice
Design (only the block diagram) an Armstrong indirectly FM modulator to generate an FM carrier with a carrier frequency of 98.1MHz and df (frequency deviation) =75kHz.A narrowband FM generator is available at a carrier frequency of 100 KHz and a (frequency deviation) df=10Hz.The stockroom has an oscillator with an adjustable frequency in the range of 10 to 11MHz.There are plenty of Frequency multipliers.