1- What is the LED current in Fig. 12-51a when VGS = 5 V? 2- The relay of Fig. 12-516 closes when VGS=2.6 V. What is the MOSFET current when the gate Voltage is high? The current through the final load resistor? VDD +30 V VDD +20 V RELAY RL 202 +VGS (a) RD 1 ΚΩ VN10LM +VGS Figure 12-51 RD 1kQ BS107 (b)

1- What is the LED current in Fig. 12-51a when VGS = 5 V? 2- The relay of Fig. 12-516 closes when VGS=2.6 V. What is the MOSFET current when the gate Voltage is high? The current through the final load resistor? VDD +30 V VDD +20 V RELAY RL 202 +VGS (a) RD 1 ΚΩ VN10LM +VGS Figure 12-51 RD 1kQ BS107 (b)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. From the given circuit, calculate the voltage required to turn on the UJT. R1 C1 0.1 uF VBB +20V 680 R3 68 Circuit for Problem 1 and 2 UJT Specifications VP = 14.5 V IP = 500 UA Vv = 3.5 V lv = 6mA n = 0.6
For the circuit shown in figure. For the circuit shown in Figure IF IB= 40 MA , VBB= 6v, RE= | Ksr, P= 80o FRc Re VeB Re The value of IE is . . mA..* О 3.24 O 4.24 O 5.24 O 6.24 O 1.24 O 2.024 The value of RB is . Kohm.. * O 52.5 O 55.5 O 47.5 O 57.5 O 25.5 O 48.5 The value of Vce is .. volt. NOTE: USE Rc= 3 Kohm, and Vcc= 15 volt. * O 5.04 O 2.04 1.04 O 4.06 O 4.04 O 3.04 O O O O O ООО О о
3.→ Ann-channel JFET having a pinch-off voltage of-3.9 V has a saturation current of 2.6 mA when VGS 1 V. What is its saturation current when (a) VGS=0 V and (b) VGS-2-V?↓
Contd) in figure below 18 The amplifies uses a voltage shoun Sousce with Rs=g0on and with following pasameters – Im=0-2 AN, T = 100n, Ybe=IK, e= BOK, ñ model Ce= 200PF, C, =4pF. Draw the hybsid n and calculate fe and f7. Vcc GOK Vo Rs 12K 330N
2. For the circuit shown in the figure below find the following a. Write the name of the circuit....... b. Find the value of IB, IC and VCE c. Draw the DC load line d. Mark the operating point or Q-point [assume ß-100 and VBE=0.7V] 23-202 RB www 270 KQ VBE +Vcc 20V Rc 2.0 K VCE RE=1 KQ
5. For the circuit shown in the figure below find the following a. Write the name of the circuit..... b. Find the value of IB, IC and VCE c. Draw the DC load line d. Mark the operating point or Q-point [assume ß-150 and VBE=0.7V] RB www 150ΚΩ G +Vcc 20V VBE Rc SKΩ VCE * 10ΚΩ - VEE -20V
Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC coupling capacitors. 5 VIO C1 RF Q1 C2 fem RL Vo
Q-4. When VGs of a JFET changes from -3.1 V to -3 V, the drain current changes from 1 mA to 1.3 mA. Then the value of trans-conductance is .
1. For the circuit of Figure 12–1, if ß = 200, then Iç is approxi- mately (a) 2.2 mA 2. In the circuit of Figure 12-1, if B of the transistor increases, then %3D (b) 3.9 mA (c) 4.8 mA (d) 14.3 mA (a) Ig decreases (d) all of the above 3. The collector saturation current for the circuit of Figure 12-1 is approximately (a) 4 mA 4. At cutoff, the collector-to-emitter voltage for the circuit of Fig- ure 12-1 is (a) 5 V (b) Iç increases (c) VCe increases ( ) (b) 6 mA (c) 10 mA (d) 15 mA (b) 7.5 V (c) 10 V (d) 15 V + 15 V 2.7 k2 RB 560 kN Vc V8 2N3904 Figure 12-1 Schematic diagram of circuit
Determine the approximate value of Ipss of the given circuit below. VDD 20V 2.1ka Q1 V. =.4.5V V, = 1.5 V 1MQ 4700 O 8.33 mA 9.82 mA 10 mA O 7.18 mA
12.0 V 4 kN 60 kN Vo Figure 4 Vi = 2.0V, a.c OV Given that VeE= 0. 7V, the input voltage 1=2.0 V sinusoidal a.c and the d.c gain for the transistor is 50 calculate i) the base current (ii)collector current (iithe output voltage Vo iv) on the same axes sketch the graphs to show how the input voltage and the output voltage vary with time
VIN = 5.3V. Determine Io1 (in mA) ? %3D 20 K2 30 k2 I0Krz a. 0.325 Voi O b. -0.397 C. -0.325 40kz op amp #! o d. ±25 p amp #2 e. 0.397