13

.docx

School

Schoolcraft College *

*We aren’t endorsed by this school

Course

NETWORKS

Subject

Computer Science

Date

Apr 29, 2024

Type

docx

Pages

4

Uploaded by ChefTankFox27 on coursehero.com

Packet Tracer - Use Ping and Traceroute to Test Network Connectivity Addressing Table Device Interface IP Address / Prefix Default Gateway R1 G0/0 2001:db8:1:1::1/64 N/A G0/1 10.10.1.97 255.255.255.224 N/A S0/0/1 10.10.1.6 255.255.255.252 N/A 2001:db8:1:2::2/64 fe80::1 R2 S0/0/0 10.10.1.5 255.255.255.252 N/A 2001:db8:1:2::1/64 S0/0/1 10.10.1.9 255.255.255.252 N/A 2001:db8:1:3::1/64 fe80::2 R3 G0/0 2001:db8:1:4::1/64 N/A G0/1 10.10.1.17 255.255.255.240 N/A S0/0/1 10.10.1.10 255.255.255.252 N/A 2001:db8:1:3::2/64 fe80::3 PC1 NIC 10.10.1.98 255.255.255.224 10.10.1.97 PC2 NIC 2001:db8:1:1::2/64 fe80::1 PC3 NIC 10.10.1.18 255.255.255.240 10.10.1.17 PC4 NIC 2001:db8:1:4::2/64 fe80::1 Objectives Part 1: Test and Restore IPv4 Connectivity Part 2: Test and Restore IPv6 Connectivity Scenario There are connectivity issues in this activity. In addition to gathering and documenting information about the network, you will locate the problems and implement acceptable solutions to restore connectivity. Note: The user EXEC password is cisco . The privileged EXEC password is class .
Instructions Part 1: Test and Restore IPv4 Connectivity Step 1: Use ipconfig and ping to verify connectivity. Click PC1 and open the Command Prompt . Enter the ipconfig /all command to collect the IPv4 information. Complete the Addressing Table with the IPv4 address, subnet mask, and default gateway. Click PC3 and open the Command Prompt . Enter the ipconfig /all command to collect the IPv4 information. Complete the Addressing Table with the IPv4 address, subnet mask, and default gateway. Use the ping command to test connectivity between PC1 and PC3 . The ping should fail. Step 2: Locate the source of connectivity failure. From PC1 , enter the necessary command to trace the route to PC3 . What is the last successful IPv4 address that was reached? 10.10.1.97 The trace will eventually end after 30 attempts. Enter Ctrl + C to stop the trace before 30 attempts. From PC3 , enter the necessary command to trace the route to PC1 . What is the last successful IPv4 address that was reached? 10.10.1.17 Enter Ctrl + C to stop the trace. Click R1 . Press ENTER and log in to the router. Enter the show ip interface brief command to list the interfaces and their status. There are two IPv4 addresses on the router. One should have been recorded in Step 2a. What is the other? 10.10.1.6 Enter the show ip route command to list the networks to which the router is connected. Note that there are two networks connected to the Serial0/0/1 interface. What are they? Type your answers here.10.10.1.10, 10.10.1.8/30, 10.10.1.10/32 Repeat steps 2e through 2g with R3 and record your answers. Click R2 . Press ENTER and log into the router.
Your preview ends here
Eager to read complete document? Join bartleby learn and gain access to the full version
  • Access to all documents
  • Unlimited textbook solutions
  • 24/7 expert homework help