Complete the following table.
Dimensions | ||||||||||
Quantity | SI Units | M | L | T | Θ | N | J | I | ||
Example | Acoustic impedance | (Pa s)/m | 1 | –2 | –1 | 0 | 0 | 0 | 0 | |
(a) | Circuit resistance | V/A | ||||||||
(b) | Luminous efficacy | cd/W | ||||||||
(c) | Thermal conductivity | cal/(cm s oC) |
Fill the appropriate dimensions for given quantity and complete the table.
Answer to Problem 1ICA
The completed table of appropriate dimension for given quantity is shown in Table 1.
Explanation of Solution
Given data:
The SI unit of circuit resistance is
The SI unit of luminous efficacy is
The SI unit of thermal conductivity is
Calculation:
Refer to Table 9-1 in the textbook for fundamental dimensions and base unit.
Refer to Table 8-1 in the textbook for common derived units in the SI system, to find the fundamental dimension of voltage.
Substitute M for kg, L for
Find the fundamental dimension of resistance.
Substitute
Luminous efficacy is the measure of visible light produced by the source and is the ratio of luminous flux to power.
Fundamental dimension of luminous flux (cd) is J.
Find the fundamental dimension of power.
Refer to Table 8-14 in the textbook for summary of electrical properties.
Substitute
Substitute J for cd and
Calories can be measured in terms of Joules.
Find the fundamental dimension of thermal conductivity.
Refer to Table 8-11 in the textbook for dimension of energy, to represent the dimensions of required parameters.
Substitute J for cal in equation (2) to find the thermal conductivity in terms of Joule.
Substitute
Obtained dimensions for circuit resistance, luminous efficacy and thermal conductivity is tabulated in Table 1.
Table 1
Dimensions | |||||||||
Quality | SI Units | M | L | T | N | J | I | ||
Example | Acoustic impedance | 1 | 0 | 0 | 0 | 0 | |||
(a) | Circuit resistance | 1 | 2 | 0 | 0 | 0 | |||
(b) | Luminous efficiency | 0 | 0 | 0 | 1 | 0 | 0 | ||
(c) | Thermal conductivity | 1 | 1 | 0 | 0 | 0 |
Conclusion:
Thus, the completed table of appropriate dimension for given quantity is shown in Table 1.
Want to see more full solutions like this?
Chapter 9 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Additional Engineering Textbook Solutions
Statics and Mechanics of Materials (5th Edition)
Mechanics of Materials
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Mechanics of Materials (10th Edition)
Engineering Mechanics: Statics
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
- Multimeter Q2) A transducer is used to measure the air pressure inside a closed container, and it generates an analog signal with respect to pressure (shown in the figure). It is known that relationship between pressure and the output current (I) as below: Pressure transducer Valve P=C¡I+C2 Pressurized Also, the observations during two different pressure measurement processes are given below: Air, P |Ah Rigid container Manometer I (mA) Ah (mm) Mercury SG=13.5 4.6 mA 0 mm 8.4 mA 420 mm Considering all above given information, calculate the output current when the pressure in the container is 13.75 kPa. (Note that manometer is filled with mercury with specific gravity of 13.5. Pwater= 1000 kg/m³) (25)arrow_forward1:54 3.11 A satellite in earth orbit has perigee and apogee radii ofr, = 7500km and r, = 16,000 km, respectively. Find its true anomaly 40 min after passing the true anomaly of 80°. (Ans.: 174.7°)arrow_forwardThe stress profile shown below is applied to six different biological materials: Log Time (s] The mechanical behavior of each of the materials can be modeled as a Voigt body. In response to o,= 20 Pa applied to each of the six materials, the following responses are obtained: 2 of Maferial 6 Material 5 0.12 0.10 Material 4 0.08 Material 3 0.06 0.04 Material 2 0.02 Material 1 (a) Which of the materials has the highest Young's Modulus (E)? Why? Log Time (s) (b) Using strain value of 0.06, estimate the coefficient of viscosity (n) for Material 6. Stress (kPa) Strainarrow_forward
- Check the following equation for dimensional homogeneity: mv = = 1.5² (Fcose) dt where m is mass, v is velocity, F is force, is an angle, and t is time. Check that each term in the equation has the following dimensions: [MªLbTC] where you are to choose the coefficients a, b, c. Answers: a = i b = i C=arrow_forwardA 2 cm thick steel pipe (thermal conductivity 43 W/[m °C]) with 6 cm inside diameter is being used to convey steam from a boiler to process equipment for a distance of 40 m. The inside pipe surface temperature is 115°C, and the outside pipe surface temperature is 90°C. If there is 600kW of heat loss, what is the thickness of the pipe?arrow_forwardUse the following TTT Diagram for the following questions: 800 A 1400 -Eutectoid temperature 700 1200 600 1000 500 800 400 600 300 Mistart) 200 50% 400 M+A M(50%) M(90%) 100 200 10-1 10 102 103 10 105 Time (s) Temperature ("C) Termperature (°F)arrow_forward
- 4:17 .l 86% google.com Water flows from point A to points D and E as shown. Some of the flow parameters are known, as shown in the table below. Determine the unknown parameters. Q1 V1 Q2 V2 D2 Qa V3 D3 D D: Q4 V4 A в D4 E Section Diameter [mm] | Flow rate [m³/s] Velocity [m/s] |AB BC 350 222 ??? 2?? Q3=2Q4 |Q«=0.5Q. 750 1.5 ??? 150 1.7 ??? CD СЕ C Chegg Visit Solved: Water Flows From Point A To Points D And E As Show ... Images may be subject to copyright. Learn more Related images O V tees f p A p Dd p E e ies ef pie de Gm t eeesnde pe the e be ple the er de e N d k hee may etheme4 Water fows fhem peint Ato pos Dand E as shon Sone of the flow parancters are knon, ashown in the able below Drenine he ukow paranem Sertan Dia r Phee rate Veleci jas LAB BC elect ja w y 150 ate K lo H- | Solved: Q3) Water Flows From Poi. chegg.com Solved: Quiz 2 Water Flows From P... TOTAL chegg.com Water flows theoagh a 150 m diameter horintal pipe at the steady ma flow rate of 60kg/s A meticn i fitted…arrow_forwardWater flow with a density of 998 kg / m3 at 70 ° C enters the system at a speed of 0.5 m / s and a 20 cm diameter pipe is pumped to a 2.5 m high reservoir with the help of a 7.5 kW pump. With the heater at the exit of the system, 1300 kW of energy is transferred to the water flow. Calculate the exit temperature of the water. (With reference to the height Z1, Z2 = 2.5 m is acceptable, ignore kinetic energy changes.) heater Pa pump and turbine P1 Ws reference plane O--arrow_forwarda) Sydney tap-water has a fluid electrical conductivity (EC or σ) of approximately 210μS/cm. Express this in terms of Ohm metres (resistivity) and mS/m (conductivity). b) The fluid electrical conductivity (EC) was measured on a water sample first at 25 °C to 305 μS/cm, then later at 20 °C to 272 μS/cm. Assuming a linear relationship, calculate the EC at 10 and 30 °C. c) A 20 cm long cylinder with 10 cm diameter is filled with an undisturbed fully saturated sandstone core. A current (I) of 100 mA was passed through the cylinder and a voltage(V) of 10,700 V was measured. Calculate the resistance and the resistivity of the sample. d) If we further know that the porosity is 1%, can you estimate the fluid electrical conductivity?arrow_forward
- Fit a power law model to the rheological behavior presented in the data: T [=]D/cm^2 y[=]1/2 1 3 2 - 3 30 4 52 5 80 6 100 7 130 8 160 9 175 10 190 11 218 12 240 13 265 (The second data in the table is not necessary to solve it.)Help yourself with matlab to solve it with the following formula: (Photo)arrow_forwardLab 2-Measurement Asynch - Tagged.pdf Page 4 of 7 ? Part I: Taking Measurements & Estimating Uncertainties for a single measurement www.stefanelli.eng.br The mass of the object is_ 0 i Parts on a tripie peam palance 0 0 10 20 30 1 100 2 3 40 200 4 +/- 50 60 70 5 300 7 400 80 Qv Search 8 90 9 500 100 9 10 g www.stefanelli.eng.brarrow_forwardIn this lab we will drop a steel ball (Psteel = 8000 kg/m³, rball = 2.18 x10³ m) through the air (Nair = 1.8 x105 Pa.s, Pair = 1.29 kg/m³), and through a viscous soap solution (Nsoap = 9.0 Pa.s [you will measure this number in the lab, but use this number for the prelab], Psoap = 1000 kg/m³). %3D 1 Pa = 1 N/m?. Calculate the terminal speed of the ball falling through the air, assuming that inertial drag is the dominant contributor. (For a sphere CD = and A is the area of the circle of radius r of the ball). Neglecting drag, estimate the time in seconds it takes for the steel ball to reach the terminal speed found in part 2 (i). Neglecting drag, estimate how far the ball would have travelled before reaching its terminal speed and comment on whether it is reasonable to neglect drag when studying the motion of this ball as it falls through the air from rest from the top of a 30 cm tall beaker or even from the ceiling of the room. Neglecting drag it would take 36 m to reach the terminal…arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning