Describe the differences between mechanization and automation

Q: When a refrigeration system that produces low or no cooling has high suction pressure and low head p...

A: For high pressure suction to occur you may have insufficient compressor which means your refrigerato...

Q: In the Four-bar linkage shown in the figure below Va= 60in/sec. A and B are points in the same link....

A: Given Data Velocity of link A is: vA=60 in/sec The horizontal distance from O to B is OB=82-2+32=3...

Q: Cylindrical samples of steel, glass and rubber are each subjected to a gradually increasing tensile ...

A: The above behavior of the material is purely based on obeying the hook's law.

Q: The inner spring of a compound helical spring is arranged within and concentric with the outer one a...

A:

Q: The converging–diverging nozzle shown in Fig. P3.22expands and accelerates dry air to supersonic spe...

A: Inlet Area, A1=π0.0124 Outlet Area, A2=π(0.025)24 P1=284000Pa T1=665K P2=8000Pa T2=240K V1=517m/s

Q: In a game of billiards, ball A is given an initial velocity v0 along the longitudinal axis of the ta...

A: Before impacts and After Impacts Equations are as follows: Conservation of linear momentum: 

Q: 2. You are working at a company that uses cooked eggs in one of your processes. Imagine that you can...

A:      

Q: For the velocity field in u = Ax , υ = By , and w = Cxy , the convectiveacceleration in the x-direct...

A: To find out the convective acceleration in the x-direction ax=ududx+vdudy+dudt  

Q: What equation would you use to find variation in the stress of a bent beam?

A: Let's assume a cantilever beam and a force F is applied at the end as shown: We can calculate the v...

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a mass flow...

A:

Q: Water at T1 fills a rigid container. The water now is heated until its temperature reaches to T2 at ...

A: Exergy is also termed as a availability or it is a ideal work. Exergy is the amount of work carried ...

Q: Consider a cylinder of specific gravity S< 1 floating ve tically in water (S = 1), as in Fig. P2.142...

A: The specific gravity of water is 1. Draw the positions of metacenter (M), the center of gravity (G),...

Q: For the long (into the screen) triangular enclosure shown below, find the view factor from surface 1...

A: From summation rule of shape factors: F33+F32+F31=1     .....(1) Since no energy radiated by surface...

Q: The tool life equation for HSS tool is VT0.14f 0.7d 0.4 = Constant. The tool life (T) of 20 min i...

A: Given data: The initial tool life is T = 20 min. The initial velocity is V = 40 m/min. The initial ...

Q: answer 69

A: Given: P1=500 kPaP2P=500 kPav1=1 m3/kgv2=2 m3/kg

Q: How is constant amplitude sustained in forced oscillations?

A: When the oscillation is carried out by external force then this is known as forced oscillation.  

Q: The Figure shows metallic crane with mass of 5000 kg. The crane is pulling a force upwards at an ang...

A: Given: mass of the crane is 5000 kg mass of the metal block is 3000 kg.  Free=body diagram of the cr...

Q: A single – stage air compressor has a cylinder bore of 0.1m, a stroke of 0.075m and a clearance fact...

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If y...

Q: I need this issue resolved correctly within 10 minutes. Please help me immediately

A:

Q: Question 6.2

A: Given Values Length of the cantilever is 6 m Triangular load applying on the beam is 1.0 kN/m Length...

Q: Define dimensional homogeneity.

A: Dimensional homogeneity  It is a concept that the dimension of variables on both sides of an equatio...

Q: 12-65. The jet plane starts from rest at s = 0 and is subjected to the acceleration shown. Determine...

A: To find out the speed of the plane From  a-75s-0=50-751000-0a=75-0.025s   vds=ads ∫0vvdv=∫0s(75-0.02...

Q: Question 6.13

A:

Q: 150 Ib/ft 100 lb

A: Consider the member AB and drawing FBD as shown below, Balancing vertical forces,Ay+By=150×5Ay+By=7...

Q: A water tower is used to supply a fire protection system as shown in Figure 10.5. The water tower an...

A: Given that, Head of the water, H=24.4 m,Length of the pipe, L=182.9 m,Diameter of the pipe, 101.6 mm...

Q: The wheel of radius r = 300 mm rolls to the right without slipping and has a velocity vO= 3 m/s of i...

A: For the given condition we have the following equationVo=rω3m/s=0.3m×ωω=10 rad/sNow velocity at poin...

Q: The cantilevered beam has a rectangular cross-sectional area A, a moment of inertia I, and a modulus...

A: Draw the free body diagram for the above system. The form factor FS for rectangular cross-section i...

Q: Include a free body diagram* For the given system of blocks below, (a) determine the direction of mo...

A: Drawing the free body diagram of the system as shown below, Let us consider that block B moves upwa...

Q: 5) What are the major kinds of mechanical loads experienced by muscle, tendon and bone?

A: The primary loads on our body tissues comprises of three which are compression, tension, and shear.

Q: Three separation unit operations – disc screen, magnet, and air classifier – are available for use i...

A: Rejection factors for each operation are given in the table. 'f' represents the rejection factor. Pa...

Q: Round everything to four decimal places. Provide solution in this format: Given, Required, Solution ...

A:

Q: Please solve these two for me

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: The chill felt on a cold windy day is related to the increase in the heat transfer coefficient betwe...

A:

Q: 11.53 A farmer lifts his hay bales into the top loft of his barn by walking his horse forward with a...

A: Constant velocity of the horse in the horizontal, vx = 1ft/s    Distance of the horse on the horizon...

Q: For the beam and loading shown, consider section n–n and determine (a) the largest shearing stress i...

A: Considering the section n-n we see that our V=80 kN. To find the Moment of Inertia of the rectangula...

Q: A 12-m pole supports a horizontal cable CD and is held by a ball and socket at A and two cables BE a...

A: The free-body diagram of the whole structure is: The value of angle ϕ is zero therefore the directi...

Q: A 6.5-m ladder AB leans against a wall as shown. Assuming that the coefficient of static friction μs...

A: Given: The length of the ladder is L=6.5 m. The coefficient of static friction is μs. The expressi...

Q: A weight of 10 N resting on an inclined plane at 30° to the horizontal is connected by a string pass...

A: Draw the free body diagram of the body 1:   Consider the equilibrium of forces acting normal to the...

Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented fr...

A: Given,  H1=7cm=0.07mH2=9cm=0.09m Area of top bar R=3×3 cm=9×10-4m2Area of bottom bar Q=7×7cm=49×10-4...

Q: Activity 2. The tripod shown supports a load P = 1500 N. Compute the force in each leg of the tripod...

A: Given data: The distance of A in vector form is A→=0i^+6j^+0k^ The distance of B in vector form is B...

Q: True/False The best filter is the one that gives the highest collection efficiency with the lea...

A: The best filter is the one that gives the highest collection efficiency with the least pressure drop...

Q: Pile drivers are heavy, metal hammer used to drive posts into the ground when constructing a buildin...

A: According to the Newton's first law of motion Body continues to be in rest or in motion unless and u...

Q: The 3 hinged parabolic arch shown below, has a span of 160m. The two supports are hinged and third h...

A: Data given - L = 160 m RB = 95.25 kN HB = 336 kN  

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.