Concept explainers
Why is it desirable to remove the autotransformers from the line when the motor reaches its rated speed?
Explain the reason why it is desirable to remove the autotransformer starters from the line when the connected motor reaches its rated speed.
Explanation of Solution
Autotransformer starter is placed between the motor and supply power lines to limit the supply voltage that is provided across the terminals of the motor during accelerating of the connected motor. With the lower accelerating voltage, motor draws less current and produces less torque in motor. Taps are provided on the autotransformer starters to permit the user to initiate the motor at an increasing speed from 50 percent, 60 percent, 75 percent or 85 percent of the line voltage.
The autotransformer starters are removed from the line connection when the motor attains the rated speed to obtain the required electrical energy by removing the magnetizing current, iron, and copper losses. Generally, the insulating life of the autotransformers may extend due to reduced heat and voltage applications.
Conclusion:
Thus, the reason why it is desirable to remove the autotransformer starters from the line when the connected motor reaches its rated speed is explained.
Want to see more full solutions like this?
Chapter 27 Solutions
Electric Motor Control
- Shunt generator will build up its voltage when: Olts field resistance higher than critical value. Olts field resistance is less than critical value.arrow_forwardIn a three phase induction motor, voltage between the slip rings at standstill is 50 V. At full load the slip is 0.04. The voltage between slip rings at full load is?arrow_forwardA. The DC motor in Figure 3 on Worksheet 8 is aa) cumulatively connected short-shunt compound DC motor b) cumulatively connected long-shunt compound DC motor c) differentially connected short-shunt compound DC motor d) shunt DC motorB. Is the DC motor in Figure 1 on Worksheet 8 turning in the same direction as that in Figure 3?a) yes b) noarrow_forward
- 23. When the circuit breaker is always tripping, most likely There is an overloading c. The supply line are open a. b. There is an over current d. The load is removed 24. The synchronous motor is not inherently self- starting because the rotating magnetic field does not have enough poles b. the rotating magnetic field is produced by only 50 HZ frequency currents the force required to accelerate the rotor is to the synchronous speed in an instant is d. the starting devices to accelerate the rotor to near synchronous speed is absent 25. Synchronous motor has speed a. slight drop in speed on full load b.high speed at low torque а. с. c. constant speed d. low speed at high -arrow_forwardc) What is the physical meaning for each of the following induction motor parameters: R1 „R2 ,Rc ,X1 ,X2 ,Xm ? What is synchronous watt?arrow_forwardWhy it is much prefer in alternator to have station armature androtating poles?arrow_forward
- 4- A double squirrel-cage induction motor has (a) Two series winding in stator (b) Two parallel windings in stator (c) Two parallel winding in rotor (d) Two rotors moving in opposite direction 5 The rotor slots are slightly skewed in squirrel cage induction motor to ---------- (a) Increase the strength of rotor bars (b) Reduce the magnetic hum and locking tendency of rotor (d) Provide ease of fabrication (c) Economize on the copper to be used 6- Stable operation of an induction motor is (a) Between zero slip and unity slip (b) Between zero slip and slip corresponding to maximum torque (e) Between 6.5 slip and 0.95 slip (d) Between slip corresponding to maximum torque and unity slip 7- Iron loss in the rotor of a 3-phase induction motor is negligible due to (a) Very low frequency of emf induced in the rotor (c) Very low flux density in rotor parts (b) Very low emf induced in the rotor (d) Constant magnitude of flux linking the rotor corearrow_forwardWhat is armature and reaction, how does armature reaction affect alternator voltage according to load load type? explainarrow_forwardHow do malfunctions occur in asynchronous motor windings? Please explain.arrow_forward
- One type of failure that's more common with 200 HP motors than with 10 HP motors is A. rotor bar failure.B. contactor failure.C. bearing failure. D. stator failures.arrow_forwardQ2] Fill in the blank (9 Marks) 1-The current drwan by the armature of D.C. motor is directly proportional to 2- The speed of a D.C. shunt-wound motor will shunt field regulator is increased. 3- The synchronous speed of a three-phase induction motor is number of pairs of poles. Rotor copper losses Rotor input power in induction motor = 5- A 4-pole three-phase induction motor has a synchronous speed of 25 r.p.s. The frequency of the supply to the stator is_ Hz. 6- The power input to a mains transformer is 200VA. If the primary current is 2.5A, the secondary voltage is 2V and assuming no losses in the transformer, the turns ratio step down. is 7- A 200kVA transformer has an iron loss of 1 kW and full load cu loss of 2 kW. Its load kVA corresponding to maximum efficiency is kVA. 8- If cu loss of a transformer at 7/8th full load is 4900 W, then its full-load cu loss would be watt. 4- if the value of resistance of the proportional to the 9- The slight curvature at the lower end of the open…arrow_forwardQ2- Indicate whether the following statements are true or false and correct the false statements 1- The brushes of d.c machine always are placed at the magnetic neutral axis 2- The field current of d.c shunt generator is not affected by load current. 3-The armature voltage of d.c series generator is not affected by load current. 4- A lap winding is most suitable for higher voltage rating machines 5- In de generator, the critical resistance can be increased by increasing its speed 6-In LAP winding the front pitch equal to (yr Ye- yb). 7- The speed of d.c series motor is decreased if the armature current is decreased 8- The compensating winding carrying the field current 9- By tapping field method, the speed of d.c series motor can be controlled below rated value 10- To solve the Commutation Problem in small machines, this can be achieved by increasing the brush widtharrow_forward