Concept explainers
An instrumentation amplifier requires separate power supplies for the input and output sections.
Whether the given statement is true or false.
Answer to Problem 1TFQ
The statement is false.
Explanation of Solution
Given:
The separate power supply for the input and the output sections for the instrumentation amplifier.
An instrumentation amplifier is also a kind of the differential amplifier which is optimized for the high input impedance and the CMRR value is also very high.
The circuit diagram is given as:
It is use to measure the low differential signal voltage which can be superimpose on the common mode voltage which is generally very larger than the voltage signal.
The common power supply for the both input and the output sections of the instrumentation amplifier.
Therefore, the given statement is false.
Want to see more full solutions like this?
Chapter 20 Solutions
Electronics Fundamentals: Circuits, Devices & Applications
- is the amount by which an electrical signal is amplified or increased. Amplification Switching none of these Gainarrow_forwardIn inverting amplifier ,the input signal is connected with pir pin .arrow_forwardDesign a Buck Converter with the Following Features. Input Voltage = 50 V Output Voltage = 20 V Switching Frequency=6 KHz Output Power = 300 W Efficiency =%85 Current fluctuationı <%10*Input current Output Voltage Ripple<%1*Output Voltagearrow_forward
- How can the amplitude of the output voltage be increased?arrow_forwardThe resolution of a 12 bit Analog to Digital converter in percent is (a) 0.01220 (c) 0.04882 (b) 0.02441 (d) 0.09760arrow_forward1-C) Which op-amp IC is more suited for digital applications, and why?1-D) Which op-amp IC is more suited for instrumentation applications, and why?arrow_forward
- 1. A displacement transducer has the following specifications: Linearity error: ±0.25% reading Drift: ±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V dc Output: 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltme- ter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Estimate an uncertainty in a nominal displacement of 2 cm at the design stage. Assume 95% confidence. 2. The displacement transducer of Problem 1 is used in measuring the displacement of a body impacted by a mass. Twenty measurements are made, which yield Determine a best estimate for the mass displacement at 95% probability based on all available information.arrow_forwardWHAT ARE FREQUENCY DEMODULATORSarrow_forwardwhat is the Rin, Rout, gain in given figurearrow_forward
- The input stage of an Op-amp is usually Differential amplifier class B push-pull amplifier Class A amplifier CE amplifierarrow_forwardQuestion 1. Design a Boost Converter circuit by drawing according to the Values given below.Input Voltage= 20 VOutput Voltage=110VSwitching Frequency=50Output Power=500 WEfficiency=90%Current ripple <1%*Input currentOutput Voltage Surge<1%*Output Voltagearrow_forwardif you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20 KHz then find. Cutoff frequency=.......... 01000 O2000 03000 O4000arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,