Degarmo's Materials And Processes In Manufacturing
Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
bartleby

Videos

Textbook Question
Book Icon
Chapter 10, Problem 1RQ

What are some of the advantages to the consumer of standardization and of interchangeable parts?

Expert Solution & Answer
Check Mark
To determine

Advantages to the consumer of standardization and of interchangeable parts.

Answer to Problem 1RQ

Advantages to the consumer of standardization and of interchangeable parts is listed below.

Explanation of Solution

Standardization is the technique in which number of different parts is reduced within the product. It aims on producing consistent products that meets the standard norms so that consumer is aware of the product.

Interchangeability means integration of any parts if a product fails. Interchangeable parts are the identical parts that are produced for replacement of any failed product part.

Some of the advantages to the consumer of standardization and of interchangeable parts is listed below.

  • Mass- production of products in large volume
  • High speed automated equipment
  • Low cost per unit
  • Integration of identical products if a product fails

Conclusion:

Thus, advantages to the consumer of standardization and of interchangeable parts is listed below.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A datum when used in manufacturing is primarily used for?     Define the functional relationship to another feature on a part, or they have a functional relationship in an assembly. They are the origin from which many Geometric tolerances are measured.     Datums are used to describe how one part must fit or align to a mating part.     A datum should be placed on the smallest surface of the part to be sure that the mating part would fit.     Datums assure that parts will always fit together.
Question 2 1. What is a First Article Inspection and why it is needed? Explain briefly (with the help of the following drawing)the steps that you take to prepare FAI in terms of design, manufacturing, and inspection of any part First Article Inspection Requirements RAW MATERIAL DRAWINGS, STANDARDS, SPEC SHEETS SPECIAL PROCESSING REQUIREMENTS TEST SPECIFICATIONS PROCEDURES SPECIAL PROCESSES (ANODIZATION, CLEANING ETC,). RAW CONVERSION FUNCTIONAL MATERIALS PROCESSES (MACHINING, CASTING ETC.) TESTING (AL6061 T6, 301SST etc.) CERTIFICATE OF CONFORMANCE TEST CERTIFICATE OF CONFORMANCE DIMENSIONAL MEASUREMENTS RESULTS MANUFACTURING ENGINEERING
What process is used to verify that a manufactured part or hardware component conforms/follows the intent of the design and customer specification? HINT: The answer is one word - not an acronym.

Chapter 10 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 10 - Prob. 11RQCh. 10 - Prob. 12RQCh. 10 - Why might you use a shrink fit to join the wheels...Ch. 10 - Explain the difference between repeatability and...Ch. 10 - When measuring time, is it more important to be...Ch. 10 - Prob. 16RQCh. 10 - What factors should be considered in selecting...Ch. 10 - Prob. 18RQCh. 10 - What is parallax? (Why do linesmen in tennis sit...Ch. 10 - Explain the rule of 10 in terms of tolerances.Ch. 10 - How does the vernier caliper work to make...Ch. 10 - What are the two most likely sources of error in...Ch. 10 - What is the major disadvantage of a micrometer...Ch. 10 - What is the main advantage of a micrometer over...Ch. 10 - What is the major difficulty in obtaining an...Ch. 10 - Why is the toolmakers microscope particularly...Ch. 10 - What are the ways that linear measurements can be...Ch. 10 - What type of instrument would you select for...Ch. 10 - What are the chief disadvantages of using a vision...Ch. 10 - What is a CMM (coordinate measuring machine)?Ch. 10 - Prob. 31RQCh. 10 - How can the no�go member of a plug gage be...Ch. 10 - What is the primary precaution that should be...Ch. 10 - What tolerances are added to gages when they are...Ch. 10 - Explain how a go/no�go ring gage works to check...Ch. 10 - Why are air gages particularly well suited for...Ch. 10 - Explain the principle of measurement by...Ch. 10 - How does a toolmakers flat differ from an optical...Ch. 10 - Prob. 1PCh. 10 - Read the 25�division vernier graduated in metric...Ch. 10 - In Figure 10.C , the sleeve�thimble region of...Ch. 10 - Suppose that in Figure 10.31 the height of the...Ch. 10 - What is the estimated error in this measurement,...Ch. 10 - Figure 10.D shows the sleeve�thimble region of...Ch. 10 - In Figure 10.E , two examples of a metric...Ch. 10 - Prob. 8PCh. 10 - Figure 10.F shows a section of a vernier...Ch. 10 - Here is a table that provides a description of...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Dimensional Analysis - in physics; Author: Jennifer Cash;https://www.youtube.com/watch?v=c_ZUnEUlTbM;License: Standard youtube license