You begin preparation of the calibration curve to measure absorbance vs concentration of FeSCN2+. To do so, you add 1.58 mL of 0.200 M Fe(NO3)3 to a cuvette and then directly add 316 µL of 0.001 M KSCN. What is the resulting concentration of FeSCN²+, assuming complete conversion of SCN¯ to FeSCN²+´ Enter your answer in units of mM to four digits after the decimal.

You begin preparation of the calibration curve to measure absorbance vs concentration of FeSCN2+. To do so, you add 1.58 mL of 0.200 M Fe(NO3)3 to a cuvette and then directly add 316 µL of 0.001 M KSCN. What is the resulting concentration of FeSCN²+, assuming complete conversion of SCN¯ to FeSCN²+´ Enter your answer in units of mM to four digits after the decimal.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A standard solution contains 100 ppm of Fe, which was found to have an absorbance of 0.151 au at 508 nm after the addition of 1,10-phenanthroline, pH 4 buffer, and hydroxylamine. Then, a water sample treated similarly exhibited an absorbance of 0.109 au. Which of the following statements is true? (A) The Fe concentration of the water sample is higher than 100 ppm. B) The Fe concentration of the water sample is equal to 100 ppm. It is impossible to estimate the Fe content of the water sample from information presented. D) The Fe concentration of the water sample is lower than 100 ppm.
A solution prepared by dissolving 2.25 g HA (MW = 51.0) and 4.00 g of NaA in 500 mL of solution has a pH of 6.02 . Calculate the Ka of the acid
A 370.00 mL solution of 0.00190 M AB5 is added to a 200.00 mL solution of 0.00165 M CD2. What is pQsp for AD5?
5. A 300.0 mg sample containing Na,CO3, NaHCO3 and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 mL to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.
5. A 300.0 mg sample containing Na,CO3, NaHCO, and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 ml to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.
I did an experiment: Molar concentration of Fe (NO3)3=.002 Molar concentration of NaSCN= .002 On my 1st trial: Volume of Fe(NO3)3 = 5 mL Moles of Fe3+, initial (mol) = 1 x 10-5 Volume of NaSCN (mL)= 1 mL Moles of SCN-,initial (mol)= 2 x 10-6 Absorbance was .08 Now trying to find Calculation of Kc I already found [FeNCS2+] equilibrium, from calibration curve (mol/L)= 2.25 x 10-5 Now I need to know: 1. moles FeNCS2+ at equilibrium (10mL) (mol) 2. moles Fe3+, reacted (mol) 3. moles Fe3+, equilibrium (mol) 4. [Fe3+] equilibrium, unreacted, 10 mL (mol/L) 5. moles SCN-, reacted (mol) 6. Moles SCN-, equilibrium (mol) 7. [SCN-] equilibrium (unreacted) 10 mL (mol/L) Feel free to just give me the formula to find these. Or to charge me 2 or 3 questions if I asked too much. Thank you!!!!!!
9.00 mL of 6.00 x 103 M Fe(NO3)3 (6.00 times 10 to the minus 3rd power M Fe (NO3)3) is added to 5.00 mL of 6.00 x 10-3 M KSCN (6.00 times 10 to the minus 3rd power M KSCN) along with 4.00 mL of water. The concentration of [F e(SCN)2*] was found to be 1.00 x 10-4 M (1.00 times 10 to the minus 4th power M) at equilibrium. How many moles of SCN" (SCN minus) are present in the solution at equilibrium? Express your answer as a decimal number (no exponents). Your Answer: Answer units
In a Complexometric Titration Experiment, the preparation of the EDTA solution is as follows: In a 250 mL beaker, weigh 0.10 g MgCl2*6H2O and 1.0 g NaOH. Add approximately 200 mL distilled water and stir to dissolve. Add about 2.0 g of EDTA and transfer the solution quantitatively to a 1-L volumetric flask. Dilute to the mark with distilled water. What is the purpose of adding MgCl2*6H2O? Please show COMPLETE solution.
7.00 mL of 5.00 x 103 M Fe(NO3)3 (5.00 times 10 to the minus 3rd power M Fe (NO3)3) is added to 6.00 mL of 7.00 x 10-3 M KSCN (7.00 times 10 to the minus 3rd power M KSCN) along with 4.00 mL of water. The concentration of [F e(SCN)2+] was found to be 3.00 x 10-3 M (3.00 times 10 to the minus 3rd power M) at equilibrium. How many initial moles of F e3+ a decimal number (no exponents). are present in the solution? Express your answer as
WARIARTAM 2. 1.2589 g of a certain brand of milk powder required 25.89 mL of 0.01873M EDTA to titrate the calcium contained in the sample. (a) What is the percent calcium in the sample? (b) Would the true result be higher, lower, or not be affected if the milk powder sample has been slightly wet?
A 0.5264-g sample containing KBr is dissolved in 50 mL distilled water. Titrating with 0.04738 M AgNO3 requires 24.57 mL to reach the Mohr endpoint. A blank titration requires 0.75 mL to reach the same endpoint. Report the % (w/w) KBr (MM = 119.0) in the sample. 51.02 % 26.19% 12.76 % 25.51 %
A 0.5131-g sample containing KBr is dissolved in 50 mL of distilled water. Titrating with 0.04614 M AgNO3 requires 25.13 mL to reach the Mohr end point. A blank titration requires 0.65 mL to reach the same end point. Report the %w/w KBr in the sample.