You are provided with a stock standard with a concentration of 100 mg/L, and a solution of unknown concentration. Prepare calibration standards using a 10 mL volumetric flask and a 1 mL piston pipette, and measure on the UV/Vis spectrophotometer (400 nm). Determine the concentration of the unknown after a 1:40 dilution, and provide the concentration of the initial solution. i need to learn how to do the calculations and draw a calibration curve to find concentration of unknown sample after i find the absorbances.

You are provided with a stock standard with a concentration of 100 mg/L, and a solution of unknown concentration. Prepare calibration standards using a 10 mL volumetric flask and a 1 mL piston pipette, and measure on the UV/Vis spectrophotometer (400 nm). Determine the concentration of the unknown after a 1:40 dilution, and provide the concentration of the initial solution. i need to learn how to do the calculations and draw a calibration curve to find concentration of unknown sample after i find the absorbances.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter27: Molecular Fluorescence Spectroscopy

Section: Chapter Questions

Problem 27.9QAP

See similar textbooks

Similar questions

What are the differences between systematic and random errors and how do they effect accuracy and precision? In what circumstances would you use standard addition (versus a normal calibration curve) to determine the amount of an analyte in a sample? A urine sample, containing analyte Z is analysed by the standard addition method where 5 mL of the original sample was mixed with increasing amounts of a Z standard and each solution diluted to a volume of 50 mL prior to analysis. A plot of the final concentration of the standard in each of the 50 mL samples (x axis) versus The measured signal from the analysis of each 50 mL sample (on y axis) produced a straight line with the general equation: y = 44.72x + 4.06 what was the final concentration of Z in the 50 mL standard addition sample? what was the initial concentration of Z in the original urine sample?
After determining the absorbance of several standards of known concentration, the trendline for a calibration curve (AKA a standard curve) plotting absorbance (y-axis) against concentration (M, x-axis) is determined to be y = 4.943x + -0.0001 The absorbance of a solution of unknown concentration is determined to be 0.48. Calculate the concentration of the unknown solution in M. Give your answer to three decimal places.
To quantify the amount of ethanol in a beverage, a technician prepared the first solution which contained 4.90 grams unknown, 1.00 grams acetonitrile, and 4.10 grams water. After the GC analysis which reported the peak areas of 5,742 for ethanol and 3,829 for acetonitrile, the technician added 0.20 grams ethanol to the first solution and ran the GC analysis again. This time, the peak areas of 6,382 for ethanol and 3,709 for acetonitrile for solution 2 were obtained. What was the percent by mass ethanol in the original beverage?
25 ml of pickled brine was taken from an apple pickled with vinegar and diluted to 500 ml, 25 ml of this was taken and acidity was determined with 0.2 N (Factor: 1.05) NaOH. In the main trials, 6.3 ml - 6.5 ml - 6.9 ml, respectively, 0.1 ml base was used in the analysis without using the sample.For example, how many ppm is its acidity?
50 Percentage Red No. 40 Soln 100% 80% 60% 40% Table 4.1: Dilutions of Red No. 40 & Absorbance Volume of Red No. 40 Soln (mL) 10me 8mL опи 4mL Percentage Red No. 40 Soln 100% 80% 60% 40% 20% Volume of DI Water (mL) OML 2mL LIML M UML 8ML Table 4.2: Dilutions of Red No. 40 & Absorbance Concentration Red No. 40 2. Report the wavelength with the maximum absorbance of Red No. 40 dye. Absorbance 20% 2ML Part A: Making a Calibration Curve for Beer's Law 1. Calculate the concentrations of each of your diluted Red No. 40 solutions and add these to Table 4.2. Show at least one sample calculation in the space below. 0.251 0.192 Total Volume 0.181 0·119 0.060 (mL) 10 mL 10 mL 10 mL 10 mL 10 mL
The following data are from the HPLC assay of paracetamol 500 mg tablets using the calibration curve method: - Weight of active ingredient in powdered tablets taken for analysis: 180 mg • Initial extraction volume: 200 mL - Dilution steps: 10 mL into 100 mL, then 5 mL into 100 mL - Linear equation: y = 12000x - 50 %3! - Area of chromatographic peak for sample is 4750. What is the theoretical concentration in final solution in mg/100 mL? (2 decimal places). Please do not write the units, just numerical value. Answer:
in a standard addition calibration method, 50.0 ml volumetric flasks were used. A 5.0 ml aliquot of a solution containing penobarbital was put in each. The solutions were made basic with KOH and mixed with different increments of 2.0 ppm standard penobarbital. The volumes were adjusted to 50,0 ml and absorbances were measured as follows 0.00 0.50 1.00 Volume added (ml) 1.50 2.00 0.33 0.48 0.64 0.80 0.96 Absorbance Calculate the concentration of phenobarbital in the unknown (Use graphical or numerical solutions) Selected Answer: 2.000 ppm 0.410 ppm Answers: 2.000 ppm 5.000 ppm 0.315 ppm
A controversy broke out as a dead body was found in a bar on Cornelia Street. The media revealed that minutes before the person died, he described his drink as something stronger than other drinks in the bar. You were the analyst tasked to verify the cause of death. Preliminary qualitative tests showed the possible presence of cyanide in the victim's death. Thus, you tried to quantitatively detect cyanide ions in the victim's drink using spectrophotometric analysis. Standard solutions were of different CN- concentrations were made as shown in Table 2. A 25.0mL aliquot of each standard solution was added with Fe(NO3)3 to form the colored complex, [Fe(CN)6]³ (aq). Each standard solution was then diluted to a total volume of 50.0 mL. The absorbances of the diluted standard solutions were recorded using 1.00-cm cells and at Amax = 725 nm and found in Table 2. Table 2. Raw absorbance measurements for each standard solution of CN-. [CN-] prior to dilution, M Abs@725nm 0.002 0.000 0.040 0.160…
After determining the absorbance of several standards of known concentration, the trend line for a calibration curve plotting absorbance (y-axis) against concentration (uM, x-axis) is determined to be y=4.244x+0.0000. The absorbance of a solution of unknown concentration is determined to be 0.604. Calculate the concentration of the unknown solution in microM. Give answer to 3 decimal places
PART ONE: Preparation of FECNS* Solution Prepare the two solutions in table 1 by accurately measuring the required volumes of distilled water and CNS into two labeled test tubes. The absorbance of the solutions must be measured soon after adding the Fe" solution from a buret. TABLE 1 Fe 5 ml 5S mL Solution Distilled Water CNS 2 mL Total Volume 3 ml 2 ml 10 ml 3 mL 10 ml In this part of the experiment you are to explore what the above quote means. As a PRELIMINARY Exercise, formulate a hypothesis as to what would happen under each of the following circumstances: 1. 1ml of 0.0020 M CNS' solution is added to the unused portion of solution 1 in the test tube 2. One drop of 0.20 M CNS solution is added to the unused portion of solution 2 in the test tube.
A solution of FESCN2+ has a concentration of 1.00 x 10-2M and an absorbance of 0.755. What is the concentration of an FESCN2+ solution with an absorbance of 0.373? Enter your answer in scientific notation, with one decimal place, as follows: 2.3e-4 or 2.3E-4 Do not include units and note that 10 and x are NOT USED in this type of scientific notation.
The amount of caffeine in an analgesic tablet was determined by HPLC using a normal calibration curve. Standard solutions of caffeine were prepared and analyzed using a 10-µL fixed-volume injection loop. Results for the standards are summarized in the following table. Concentration of Standards Signal (arbitrary units) (ppm) 50.0 8354 100.0 16925 150.0 25218 200.0 33584 250.0 42002 The sample was prepared by placing a single analgesic tablet in a small beaker and adding 10 mL of methanol. After allowing the sample to dissolve, the contents of the beaker, including the insoluble binder, were quantitatively transferred to a 25-mL volumetric flask and diluted to volume with methanol. The sample was then filtered, and a 1.00-mL aliquot was transferred to a 10-mL volumetric flask and diluted to volume with methanol. When analyzed by HPLC, the signal for the caffeine was found to be 21469. Report the number of milligrams of caffeine in the analgesic tablet.