1. A venturi meter having a diameter of 150mm at the throat is installed in a horizontal gauge partly filled with mercury (the remainder of the tube being filled with water) and connected with the meter at the inlet and at the throat, what would be the difference in level of the mercury columns if the discharge is 150 liter/sec? Neglect head loss. Do not write any unit in your answer, use 3 decimal places Unit of Ans is mm

1. A venturi meter having a diameter of 150mm at the throat is installed in a horizontal gauge partly filled with mercury (the remainder of the tube being filled with water) and connected with the meter at the inlet and at the throat, what would be the difference in level of the mercury columns if the discharge is 150 liter/sec? Neglect head loss. Do not write any unit in your answer, use 3 decimal places Unit of Ans is mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the discharge coefficient of a Venturi ...... meter has a value 0.6 1 0.92 to 0.99 O venturi meter is used for measuring the ........ discharge in tank long pipe short pipe
A Cole pitometer is set with its orifices at the center of a 40cm pipe. Determine the discharge if the deflection, z of carbon tetrachloride (s = 1.50) in the differential gauge is 325mm. Use C = 0.84 and the ratio of the mean velocity to center velocity may be assumed as 0.83. C4o cm
No. Date. Determination of Discharge Using a Venturi Meter Formula: G o Vol 29 Ge trial #1 Hi He trial #2 H 290mm trial H3 Hi = 240 mm 190m %3D 50 mm He 40mm し= 26.15 S 32.31s 34.335 complete the table below ( provide soluhion please) valume! Actual Theore tical Discharge t Drischaget C #t Fime Trial + (mm) + (mm) 2 3 CS Scanned with CamScanner
This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. What will be the gage pressure reading at A? correction: 3.75 mm should be 375 mm en Me Do not write the unit. You will only input the numerikal answer in the space provided. Unit of the Correct Answer. kPa Decimal Places required in the firal answer 3
Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage.Determine the value of H in m if the pressure at A is 142 kPa. Round your answer to 2 decimal places.
The throat area of a c-d nozzle is 10 cm^2 and its exit is 20 cm^2. If the stagnation pressure is 1 bar, what is the exit pressure (Pe) range needed to ?chock the throat greater or equal 0.935 bar O less or equal 0.937 bar O greater or equal 0.0935 bar and less or equal 0.937 bar greater or equal 0.937 bar and less or equal 1 bar O
Oil of SG 0.75 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in Kpa? A 2.75 D h B C Hg(13.6)
Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in kPa? A 2.75 h B Hg(13.6)
The ligure showWs a tank dischaPging through a pipe with a nozzle at Its end. Find the discharge and the pressure at the base of the nozzle. Losses are: Tank to the base of nozzle is 5(V/2g and through the nozzle is 0.05(Va)/2 (V, is the velocity in the pipe and Vi is the velocity at the tip of the nozzle) Water D= 150mm! D,= S0mm
An oil of specific gravity 0.89 is flowing through a horizontal venturimeter fitted to a 242 mm diameter pipe at the rate of 108 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 841 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.13 N/mm2.
A cylinder having a diameter of 6 in (152mm) and a stroke length of 25 in (635mm). The exit time will be 5 seconds. The system operates with a pressure of 50 psig (3.45 bar) and there will be a pressure loss of 2 psi. What will be the Cv of the valve to be installed? [Answer: 1.99]
In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and the loss at nozzle of 0.05 times the V2²/2g, determine the discharge and head H. Ans: 0.0136m³/s & 2.731m A 150mm dia Wit 50mm dia