With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 5 answers is correct 432.857 Ibs134.392 Ibs235.032 Ibs353.551 lbs555.334 Ibs A boom with an angle of theta, supports a1000 Ibs load as shown in the figure.Assume that the force exerted by theboom is 3 times the force exerted by thecable that holds it in place, what is theforce exerted by Cable A? *AВ1000 Ibs

The free-body diagram of the junction of the boom, given load, and the force exerted by the cable,…

Answered: With FBD and Solution pls refer to the…

Engineering

Mechanical Engineering

With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 5 answers is correct

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.8P: A plane truss has a pin support at F and a roller support at D (see figure). (a) Find reactions at...

See similar textbooks

Similar questions

A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
A plane frame has a pin support at A and roller supports at C and E (see figure). Frame segments A BD and CDEF are joined just left of joint 1) by a pin connection. (a) Find reactions at supports A. C. and E. (b) Find the resultant force in the pin just left of D.
A plane truss has a pin support at F and a roller support at D (see figure). (a) Find reactions at both supports (b) Find the axial force in truss member FE.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees
The elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate the magnitude of the force in the hydraulic cylinder AB corresponding to the 2270-Ib load supported as shown. What is the magnitude of the force in link EF? Assume W = 2270 lb, a = 2.90 in., b = 3.10 in., c = 4.45 in., d = 8.75 in., e = 1.95 in., and f = 1.95 in. W e D b. a A E Answers: AB = i Ib EF = i Ib
A boom with an angle of theta, supports a 1000 lbs load as shown in the figure. Assume that the force exerted by the boom is 3 times the force exerted by the cable that holds it in place, what is the force exerted by Cable A?
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ¢ = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb , what is the maximum weight Wmax of the crate that the system can support? What is the angle 0 required for D equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) vec ? Wmax, 0 = lb, degrees
Question 2 Find the forces in all the members of the truss shown in figure below. B 3 m 3 m 3m 40 kN 40 kN