While using ARDUINO UNO to read from a 5V sensor, the analog read 0 has a count value of620. What is the voltage applied on the pin?O a. 234 VO b.104 VOc3.03 VO d. 42.3 VThe PIC 16F84A microcontroller has a built-in ADC.O a. True.O b. False.EEPROM stands for:O a Electrically extended programmable read-only memoryO b. Enhanced erasable programmable read-only memoryOc. Electrically erasable programmable read-only memoryOd Electrically erasable product read-only memory

1) For 5V digital input, the maximum analog count value is 1023. Therefore for a count value of 620,…

Answered: While using ARDUINO UNO to read from a…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write an Assembly Language for 8051 Microcontroller which copies the data from R0 of Banko to R1 of Bank1, R2 of Bank 2, and R3 of Bank 3.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
what is the MAXIMUM number of diode OR gates that can be cascaded before the output is not recognized as logic high?
Write a gate level verilog code for Multiplexer
DIsassemble the following MIPS 32-bit hexadecimal instruction written as addr:instr 60005000 : 0c000020
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
Design a 3 bit Flash ADC so that an analog input voltage of 4 V outputs binary’100’.
The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). 8. gf a b t la Ob d Dp e d8c Dp The 7-segment to be used is of common anode type. Consequently, any segment will be ON if its input is Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will be OFF while all the others are ON. 1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input (000.101), assuming the other two combinations as don't care. 2- Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions 3- Show your design using 2-input, and 3-input NAND gates, and inverter.
Write an assembly 8051 code to count a hexadecimal digit every second and display it on the 7-segment.
1. Draw a 3-bit flash converter with Vref= 12V a.Determine the full-scale range. b.Determine the code center for each code. c.Determine all the transition voltages. d.Determine the resolution.
Consider a 4-bit ADC and full scale voltage measurement range of (-37 to 37).The Resolution will be O 4.62 O 1.75 O 0.41 O 0.41 In CRO, if the electron beam emerging from the electron gun is left alone, it will strike the screen as straight line. Select one: OTrue O False
19) Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be _________. 0.30 0.06 0.92 1.00

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

While using ARDUINO UNO to read from a 5V sensor, the analog read () has a count value of 620. What is the voltage applied on the pin? O a. 2:34V O b. 104 V Oc 3.03 V O d. 423 V ADC