Which is CORRECT? a. EDTA has 2 oxygen sites and 2 nitrogen sites that are electron rich. b. At pH = 10, fraction of fully deprotonated form of EDTA approaches to 1. c. EDTA titrations that are carried out beyond pH 10 typically involves the use of auxiliary reagents. d. As long as EDTA titrations are carried out beyond pH 10, we are sure that all of the analyte will react completely with EDTA.

Which is CORRECT? a. EDTA has 2 oxygen sites and 2 nitrogen sites that are electron rich. b. At pH = 10, fraction of fully deprotonated form of EDTA approaches to 1. c. EDTA titrations that are carried out beyond pH 10 typically involves the use of auxiliary reagents. d. As long as EDTA titrations are carried out beyond pH 10, we are sure that all of the analyte will react completely with EDTA.

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section4.9: Spectrophotometry

Problem 3.1ACP

See similar textbooks

Similar questions

Which of the following DOES NOT meet the requirement for primary standards? a. Large molar mass b. High affinity towards water c. High purity d. Soluble in titration medium
You are going to analyze a substance with the following structure. What method will be best used? CHOICES: a. Neutralization b. Direct EDTA Titration c. Indirect and Residual d. EDTA Titration e. Residual Titration Precipitation
5. A student titrated a 25.00 mL sample of water with 0.0100 M EDTA. The titration required 16.40 mL of EDTA. а. Calculate the moles of EDTA used. b. Calculate the moles of hardness in the water sample. с. Calculate the moles of hardness per liter of water. d. Calculate the ppm hardness in the water sample.
An auxiliary competing agent is used in EDTA titrations to slow down the titration. keep some interfering component of the analyte mixture from complexing with the EDTA. speed up the titration. keep the metal ion from precipitating out of the solution.
a. A deepwell water sample of 100 mL was titrated with 0.010 M EDTA at pH 10 ( with Mg-EDTA pH 10 buffer reagent) and consumed 31 mL. Calculate the Total Hardness of the water sample as mg CaCO3. b. A deepwell water sample of 100 mL was titrated with 0.010 M EDTA at pH 12 and consumed 31 mL. Calculate the Calcium content of the water sample in mg/L.
Following the monograph procedure, determine the weight in grams of sodium carbonate (MW-106 g/mol) used to standardize a 0.987 N sulfuric acid solution. 1. Consider that the burette was completely filled to the 0 mL mark before titrating. What is the volume of titrant consumed based from the image below? A. 22.9 mL B. 21.2 mL C. 21.3 mL D. 22.7 mL 2. What is the unknown weight (grams) in the problem? Your Answer:
Ivan B. Garcia A. What is the acid/base ratio? Why is it important in the titrimetric process? B. Why should you boil the sample solution right before reaching the end point? c. Does the primary standard used for the standardization of HCI fit the criteria for a good primary standard? Why or Why not?
At 40.0 mL 0.0050 M Sr2 + pH 10, 0.0100 M EDTA is titrated. Calculate the pSr for the equivalence point. Arm (SrY) = 4.3x108, α4 = 0.35 A. 5.37 B. 4.69 C. 5.33 D. 5.55
Compare the 2 quantities based on the given condition. Choose A If quantity in Column 1 is greater B If quantity in Column 2 is greater C If the two are equal D If relationship cannot be determined A. Titration of Cu2+ with EDTA B. Titration of Cu2+ with EDTA in the presence of of NH3 I. pCu at EP in A II. pCu at EP in B
Tony is showing a bacterium having high pH requirement for its growth. He then has to prepare a minimal medium at pH 9. Adding 0.5 ml of the pH indicator to 10 ml of the medium, the solution remained colorless. The pH of the medium was adjusted using 2.25 ml of the 0.05 N titrant. a. What was the pH indicator utilized? b. What is the amount of 1 N titrant needed to adjust 150 ml of minimal medium to pH 9? c.What was the titrant he used?
a. What is the structure and full name for EDTA? b. The titration of Zn^+2 and EDTA is carried out in the same manner as the Mg^+2 * EDTA titration (in fact, Zn metal may be used to standardize your EDTA solution). In this case, the ammonia from the pH 10 buffer serves an additional purpose. What is it? c. Although EDTA has, in its fully protonated form, 4 hydrogen atoms that can be lost, it is listed as a hexadentate ligand. Explain why this is the case.
3. A solution contains 1.694 mg of Coso, (155.0 g/moal) per milliliter. Calculate the volume of 0.08640 M EDTA needed to titrate a 25.00-ml aliquot of this a. solution. b. Calculate the volume of 0.009450 M Zn2- needed to titrate the excess reagent after addition of 50.00 mL of 0.008640 M EDTA to a 25.00 mL aliquot of this solution. c. Calculate the volume of 0.008640 M EDTA needed to titrate the Zn2+ displaced by Co2 following addition of an unmeasured excess of ZNEDTA2 to a 25.00-ml aliquot of the Coso, solution. The reaction is Co2- + ZNEDTA? + Zn2+ + COEDTA2-