What is the relationship of the current-voltage characteristic and the color of the Red, Yellow, Green, Blue and White LEDs? What is the difference between the current-voltage characteristic of the white LED comparing to the other lights? Is White LED similar to any other LED? When measuring the current-voltage of the 5 LED lights (Red, Yellow, Green, Blue and White) LEDs, what observation do you make? What's different about the white LED comparing to the other lights? ..

What is the relationship of the current-voltage characteristic and the color of the Red, Yellow, Green, Blue and White LEDs? What is the difference between the current-voltage characteristic of the white LED comparing to the other lights? Is White LED similar to any other LED? When measuring the current-voltage of the 5 LED lights (Red, Yellow, Green, Blue and White) LEDs, what observation do you make? What's different about the white LED comparing to the other lights? ..

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

Consider the circuits shown in figure 4. Each represents a configuration of LEDs driven by a voltage or a current source. For the purpose of this problem you can model the LED as a resistor. The intensity of the LED is proportional to the power dissipated by it. Suppose one LED burns out (i.e. becomes a open circuit), for each configuration shown determine if the intensity of the remaining LEDs becomes brighter, dimmer or stays the same. Support your answers with appropriate calculations. V (a) D ODDDDDD V (b) Figure 4: LEDs arranged in different configurations (c)
The power supply is a 9V battery and uses a Red LED whose voltage drop is 2V. The LED recommends that the "ON" current should be 10 milliamps. a. What series resistor will give the specified LED current? b. What is the power dissipated by the resistor you selected in part a? What is the power dissipated in the LED? C.
Q11. What is LED?
A 2 Volt signal travels from 50 Ohms to 75 Ohms, find the voltage at the interface. If the 2 Voltsignal travels the other way, from 75 Ohms to 50 Ohms. Find the voltage at the interface inboth cases and if it is different explain why
What are the applications of LEDs?
Please help. You are going to draw arrows that indicates the flow of the given 5 actions (a,b,c,d,e). You can draw arrows for all of them in the picture above, or make separate drawing for each letter. Please help me this is about CARRIER ACTION/FLOW OF CARRIERS in a semiconductor. It is also about Ferni Level.
1. State the applications of Clamper.2- What are the disadvantages of LED? 3- Why Si & Ge are not used in LED?
The polarization of an LED is similar to the polarization of the diode, but a current limiting resistor must always be connected in series with the LED. Both the LED and its current limiting resistor must be placed in series with the load. a) The above statement is correctb) The above statement is incorrect.
If anode of each LED of the seven-segment display is connected to the 5-V supply the chip is a _____ display. It is an active-____, because it takes a _____ to illuminate a segment. A.common-anode, LOW, LOW B. common-cathode, LOW, LOW C. common-anode, HIGH, HIGH D. common-cathode, HIGH, HIGH E. common-anode, HIGH, LOW
help me in these questions pls write the questions with the and by (Computer)1- Explain how the circuit below works to perform its main function?i. Zener diode is short circuited when voltage across it rises beyond its breakdown voltage.ii. Radiation from light emitting diode is detected by a phototransistor without having any physical contact.iii. The circuit prevents the LED from having the wrong polarity or too high voltage.iv. The circuit prevents the alternating signals by rectifying it using a diode. a. All the answers. b. i, ii and iii only. c. i, iii and iv only. d. i, ii and iv only.========2- Which of the following statement is most probably INCORRECT in explaining the working principle of an engine management system? a. Microprocessor is used to process incoming signal including position, speed, timing, flow, and temperature. b. The operation of valves and spark ignition is in sequence following the stroke action. c. The timing of the sequence is fixed.…
What is a Semiconductor? Explain the properties of a Semiconductor such as its physics, etc? you better explain a little longer and illustrated pls
Describe the purpose of a PV and PQ curves. Draw the curves and explain its position (stability & unstable areas) Describe the difference between each curve by reference to the curves and explain when each one would be used