What is the rated flywheel power for a CAT 834H four-wheel tractor equipped with a converter drive? What are the maximum speeds, for this machine, in each of its four forward gears? Determine the maximum rimpull of the tractor in each of the indicated gears if the efficiency is 92%. If the tractor is operated over a haul road whose slope is +2.5% with rolling resistance of 80 lb/ton, determine the maximum external pull by the tractor in first gear. Can the tractor climb the slope in fourth gear? The required data can be found at www.cat.com.

What is the rated flywheel power for a CAT 834H four-wheel tractor equipped with a converter drive? What are the maximum speeds, for this machine, in each of its four forward gears? Determine the maximum rimpull of the tractor in each of the indicated gears if the efficiency is 92%. If the tractor is operated over a haul road whose slope is +2.5% with rolling resistance of 80 lb/ton, determine the maximum external pull by the tractor in first gear. Can the tractor climb the slope in fourth gear? The required data can be found at www.cat.com.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and transmits a torque of 20 N-m. The torque transmitted by the gear is
2) An electric motor transmits 0.5HP at 1600RPM. A 100 tooth helical pinion having a normal pressure angle of 25° and a helix angle of 15° and a normal diametral pitch of 10 teeth/in transmits power to a 100 tooth gear. Determine the tangential, radial and axial forces on the gear tooth.
The module and the number of teeth on the pinion of a spur gear are 12mm and 15teeth respectively.A power of 400kW is to be transmitted at 1700rpm of width.if the involute teeth are of standard proportions (addendum=m) with the pressure angle of 22.5° determine (A) torque due to power delivered (B) tangential load (C) teeth width (E)load on the bearings
Draw free-body diagrams of the two gears, assuming an input couple M on theOUT X shaft of the larger gear in the direction shown. Include forces at bearings A, B, D and E. M isthe reaction couple at the output shaft - i.e. the resistance to turning of the object being driven.The gears have 48 and 24 teeth respectively. If the input gear (large gear) turns at 100 rpm(= revolutions per minute), the output speed (small gear) is _______rpm.Wil OUT X IN Xl M be larger or smaller than M ?
When designing a pair of spur gears to be used as part of the drive for a log conveyor run by an electric motor, the overload factor K0 is most likely:
80 Design a two-speed gearbox suitable to transmit 25kW. The input shaft runs at 630rpm and carries two gears, A and B. The 2nd shaft carries two sliding gears, C and D. Gear C meshes with gear A, giving the driven shaft a speed of approximately 315rpm. Gear D meshes with B giving the driven shaft a speed of approximately 215rprn. The distance between the centres of the shafis is approximately 270mm and the teeth are 20° full depth involute. Using a module of 6mm and basic stress of 120MPa for all the gears, apply the Lewis formula and calculate: No of teeth for each gear [30;23;60,67] PCD for each gear [180; 138,360;402)mm True speed of gears C and D [216;27] Correct centre distance between the shafts (270) Width of the tooth material for each gear if [A&C:47mmm; B&D:53mm] the basic stress is 120MPa, using the Lewis formula. a) b) d) e) f)
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear's teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1.1. If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1.2. Calculate the gear maximum velocity of sliding.
A parallel shaft helical gear consists of a 20 dts drive pinion And a 96 driven gear. Both gears have a transverse diametrical pitch of 20 dts / in, a helix angle of 25 and a pressure angle on = 20 . The face width is 4 in., AND the gears are moving at 1600 ft / min, on the pitch line. The impeller is made of steel UNSG 10180 CD and without heat treatment; the driven one is made of grade 30 cast iron. Based on flexural strength calculations, evaluate the capacity or safe maximum power at hp. Consider general industrial service, and nG = 4.
1. Calculate the power that can be transmitted safely by a pair of spur gears with the data given below. Calculate also the bending stresses induced in the two wheels when the pair transmits this power. Number of teeth in the pinion = 20 Number of teeth in the gear = 80 Module = 4 mm Width of teeth = 60 mm Tooth profile = 20° involute Allowable bending strength of the material = 200 MPa, for pinion = 160 MPa, for gear = 400 r.p.m. Speed of the pinion Service factor = 0.8 0.912 0.154- T Lewis form factor %3D 3 Velocity factor 3 + v
2 spur gears connected externally were produced having M-2.5. They were mounted on 2 different shafts with a center distance of 9cm. The speed ratio is 3:1. Using 14.5° determine the following: 1. Pitch Diameter (Driver Diameter) mm 2. Pitch Diameter (Driven Diameter) = mm 3. Number of Teeth (Driver) = teeth 4. Number of Teeth (Driven) = teeth 5. Circular Pitch = mm 6. Addendum = in 7. Clearance = in 8. Dedendum D in 9. Whole Depth in 10. Working Depth in %!
Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the operating pressure angle is 20° The minimum value of addendum needed to ensure continuous transmission of motion is
A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the pinion pitch and the gear is 80 mm and 100 mm. The shape of the gear gear was 14 restriction form. The static voltage allowed for both gear is 55 mpa. If the door transports to 2.95 kw power at the turn of 1200 RPM, identify the module and the number of teeth on each gear from the Angle of power and check the design from the Angle of the tear. Take the surface durability limit is 630 mpa and the modulus elasticity to iron cast is 84 kn /mm2.