What is the molarity of a potassium hydroxide solution if 38.65 mL of the KOH solution is required to titrate 25.84 mL of 0.1982 M hydrochloric acid solution? a. 0.1325 M b.0.8817 M Ⓒc. 0.2963 M Ⓒd.0.2648 M e. 0.01324 M QUESTION 9 A solution whose molarity is very accurately known is called: a. primary standard b. indicator c. standard solution d. neutral e. acidic QUESTION 10 If 20 mL of 0,010 M H3PO4 solution is completely neutralized by 60.0 mL of Ca(OH)2 solution, what is the molarity of the Ca(OH)2 solution? a. 0.030 M b. c. 0.200 M 0.0050 M d. 0.010 M e. 0.040 M

What is the molarity of a potassium hydroxide solution if 38.65 mL of the KOH solution is required to titrate 25.84 mL of 0.1982 M hydrochloric acid solution? a. 0.1325 M b.0.8817 M Ⓒc. 0.2963 M Ⓒd.0.2648 M e. 0.01324 M QUESTION 9 A solution whose molarity is very accurately known is called: a. primary standard b. indicator c. standard solution d. neutral e. acidic QUESTION 10 If 20 mL of 0,010 M H3PO4 solution is completely neutralized by 60.0 mL of Ca(OH)2 solution, what is the molarity of the Ca(OH)2 solution? a. 0.030 M b. c. 0.200 M 0.0050 M d. 0.010 M e. 0.040 M

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter7: Solutions And Colloids

Section: Chapter Questions

Problem 7.107E

See similar textbooks

Similar questions

Calcium carbonate, CaCO3, can be obtained in a very pure state. Standard solutions of calcium ion are usually prepared by dissolving calcium carbonate in acid. What mass of CaCO3 should be taken to prepare 500. mL of 0.0200 M calcium ion solution?
An experiment in a general chemistry laboratory calls for a 2.00-M solution of HCl. How many mL of 11.9 M HCl would be required to make 250 mL of 2.00 M HCl?
What volume of 0.250 M NaOH is required to react completely with 0.0100 moles of H2SO4? (a) 80.0 mL (b) 60.0 mL (c) 40.0 mL (d) 125 mL
Two liters of a 1.5 M solution of sodium hydroxide are needed for a laboratory experiment. A stock solution of 5.0 M NaOH is available. How is the desired solution prepared?
Distinguish between the terms slightly soluble and weak. electrolyte.
Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.
Graph Table 14.10 shows solubility data that was collectedin an experiment. Plot a graph of the molarity ofKI versus temperature. What is the solubility of KI at55°C?
An experiment calls for 100. mL of 1.25 M HC1. All that is available in the lab is a bottle of concentrated HC1, whose label indicates that it is 12.1 M. How much of the concentrated HC1 would be needed to prepare the desired solution?
Tris(pentatluorophenyl)borane, commonly known by its aeronym BARF, is frequently used to initiate polymerization of ethylene or propylene in the presence of a catalytic transition metal compound. It is composed solely of C, F, and B; it is 42.23% C and 55.66% F by mass. a. What is the empirical formula of BARF? b. A 2.251-g sample of BARF dissolved in 347.0 mL of solution produces a 0.01267-M solution. What is the molecular formula of BARF?
Potassium hydrogen phthalate is a solid, monoprotic acid frequently used in the laboratory as a primary standard. It has the formula KHC8H4O4. This is often written in the short-hand notation as KHP. If 25.0mL of a potassium hydroxide solution are needed to neutralize 2.26g of KHP, what is the molarity of the potassium hydroxide solution? Potassium hydrogen phthalate sometimes called potassium biphthalate, as shown on this bottle is an acid that is convenient to store and use because it is a solid.
5.00 mL sample of 0.1136 M of standard ascorbic solution required to 12.70 mL of KlO3 to reach the endpoint. The same KlO3 solution was then used to titrate 10.00 mL sample of a peach solution and it required 8.50 mL to reach the endpoint. Determine the: A.) Mass in Mg of I2 formed prior to the endpoint, and B.) Molarity of KlO3.