Water is pumped from a supply reservoir to a ductile-iron water-transmission line, as shown in Figure 2.26.The high point of the transmission line is at point A, 1km downstream of the supply reservoir, and the lowpoint of the transmission line is at point B, 1 kmdownstream of A. If the flow rate through thepipeline is 1 m3/s, the diameter of the pipe is 750mm, and the pressure at A is to be 350 kPa, then: (a)estimate the head that must be added by the pump;(b) estimate the power supplied by the pump; and (c)calculate the water pressure at B.SupplyreservoirElev. 7 mPumpElev. 10 mTransmissionlineElev. 4 m-BFigure 2.26: Water pumped into a transmission line

Given : Flow rate through pipeline = 1 m3/s dia of pipe = 750 mm Pressure at A is 350 kpa To Find :…

Water is pumped from a supply reservoir to a ducti iron water-transmission line, as shown in Figure 2.2 The high point of the transmission line is at point A km downstream of the supply reservoir, and the lo point of the transmission line is at point B, 1 km downstream of A. If the flow rate through the

Water is pumped from a supply reservoir to a ducti iron water-transmission line, as shown in Figure 2.2 The high point of the transmission line is at point A km downstream of the supply reservoir, and the lo point of the transmission line is at point B, 1 km downstream of A. If the flow rate through the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.18. Water is pumped from a supply reservoir to a ductile iron water transmission line, as shown in Figure 3.26. The high point of the transmission line is at point A, 1 km downstream of the supply reservoir, and the low point of the transmis- sion line is at point B, 1 km downstream of A. If the flowrate through the pipeline is 1 m³/s, the diameter of the pipe is 750 mm, and the pressure at A is to be 350 kPa, then: (a) esti- mate the head that must be added by the pump; (b) estimate the power supplied by the pump; and (c) calculate the water pressure at B. Supply P reservoir Elev. 7 m Pump A Elev. 10 m Elev. 4 m Transmission line B
Water transfer from down reservoir to upper reservoirWater is pumped from the reservoir for drinking purposes (see figure below). The expected flow rate is 600 m3.h-1. The water passes through a pipe (diameter of 0.3 m) with a strainer, a valve and an elbow (see figure). At the pump outlet, water flows in another pipe of 0.5 m, 800 m long before reaching a second small reservoir Coefficients of minor head losses are the following: valve KL,v = 1.2, strainer KL,s = 3, elbow KL,e = 1.9. The pipe roughness is  = 0.1 mm. The Net positive suction head NPSH of the pump at the flow rate, Q= 600 m3.h-1, is 2 m. The vapor pressure of water is pvs = 2340 Pa. The pump efficiency is 53%.1) Calculate the total head losses in the first pipe2) Is there any risk of cavitation? 3) What is the power supplied to the pump?
SITUATION 2: Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Elev 80 ha hez Elev 70 B 4000 m- 250 mm f-0.018 he 3500 m f- 0.018 Elev 60 Pipe 1: L= 5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L= 3500 m 5000 m - 300 mm f= 0.018
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
Water at 20°C is pumped at a rate of 15 L/s into a reservoir as shown in the Figure below. Between the pump and the reservoir is 150 m of 100 mm diameter PVC pipe, and the water surface elevation in the reservoir is 8 m above the centerline of the inflow pipe. The roughness height of the PVC pipe can be assumed to be negligibly small. Estimate the gauge pressure (kPa) on the downstream side of the pump. 15 L/s 133 120 111.7 131.5 Pump P - 150 m. 100 mm Reservoir 8m
a pipeline 50 cm diameter and 4500 m long connects two reservoirs (1 &2) whose constant difference of water level is 12 m, A branch pipe 1250 m long and taken from a point distant 1500 m from the upper reservoir(1) leads to another reservoir (3) whose water level is 15 m below reservoir (1) find the diameter of pipe (D3) so that the flow into both the reservoir is same if friction factor =0.0075 Select one: a. D3= 22.5 - 27.5 cm b. D3= 33.5 - 40.5 cm c. D3= 27.5 - 32.5 cm d. D3= 17,5- 22.5 cm
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
The 150-mm pipeline shown below conducts water from the reservoir and discharges at a lower elevation through a nozzle with a discharge diameter of 50 mm. The water surface in reservoir 1 is at an elevation of 30 m, the pipe intake 2 and 3 at an elevation of 25 m, and the nozzle 4 and 5 at elevation 0. The head losses are: from 1 to 2, 0; from 2 to 3, 0.6 m; from 3 to 4, 9 m; from 4 to 5, 3 m. Compute the pressure head at point 4 in m.
Tank A has an elevation of 100 m and Tank B has an elevation of 160 m. Since Tank A is lower than B, engineers have installed a pump near A to transfer fluid to B. The discharge in the pipe is at 0.65 cubic meters per second and pipe has a length of 1 km. with a diameter of 0.6 meters. If Hazen williams coefficient is equal to 120, compute the head loss in the pipe.
Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in series between two reservoirs with a difference in level of 12 m. The friction factors are 0.024, 0.021 and 0.019 respectively. The lengths are 200 m, 300m and 250 m respectively. a.) Find the flow in m^3/s in PIPE 3. b.) What is the head loss in meters in pipe 3? c.) Determine the length of an equivalent 350 mm diameter pipe.
A conduit is carrying oil ( S = 0.75 ) and its absolute viscosity is 0.25 kg / m-s. If the flow rate is 0.45 cu.m/s Determine the following • The entrance length • The length of the inviscid cone • The length of the profile development given the following situations 1. Circular pipe 800mm 2. rectangular pipe (Width = 800mm, Depth 1200mm)
A hydraulic jump is formed in a 4 m wide rectangular open channel at a short distance downstream of a control gate. The flow depth just downstream of the gate is 1.8 m and the outlet discharge is 134 m3 /s. The density of water is 1000 kg/m3 . Determine the flow depth downstream of the jump and the headloss in the jump. Express the headloss in kW per metre width. i need ansswer in 30 minutes thank u