Water is extracted from a 7mm nozzle on a semi-spherical panel where the distance between Qatar's distance Extra is extrusion and painting 30 mm Further size of water is collected 10L during the time of appreciation 1.173 min as much as the resulting force than extrusion after the opposite weight shift of extrusion is a 50 gm? Which is the largest power resulting from weight or theoretical force? o 10:02 lues /

Water is extracted from a 7mm nozzle on a semi-spherical panel where the distance between Qatar's distance Extra is extrusion and painting 30 mm Further size of water is collected 10L during the time of appreciation 1.173 min as much as the resulting force than extrusion after the opposite weight shift of extrusion is a 50 gm? Which is the largest power resulting from weight or theoretical force? o 10:02 lues /

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A mechanical press is powered by a 23-kW motor and operates at 40 strokes per minute. It uses a flywheel, so that the crankshaft speed does not vary appreciably during the stroke. If the stroke is 150 mm, what is the maxumum const.ant force rhat can be exerted over the entire stroke length?
04: In Flat Strip Open Forging (FSOF) Process, A strip ingot of length (90.5mm), width (4.75cm), and initial thickness (1.75cm), is open forging to thickness (15mm). The mean flow stress o y 280+110, and friction facter (0.065), Determine the maximum plate pressure and the press capacity at. (1) forging anset. (II) forging end. 96.5mm
A tube with outer diameter i5mm and inner diameter 10mm, is to be manufactured by direct extrusion. The billet has a diameter of Do and a length of 200mm. The product is extruded at a speed Vf Assume deformation efficiency 80% and material follows O =110(7) N / mm The extrusion pressure and power are 20 MPa and 300KW, respectively. Calculates: c) Extrusion force in KN? d) The speed Vf? e) The tube final length? ) If the power cost is 2 SR/KW.Hr what is the production cost of producing 50 bars having 2-meters length each from the same cross-section?
3G Z 4.5G+ l. Which of the following stress or .10 strength parameters is used in the computation of the force in an extrusion (operation (one best answer a) average flow stress O ,b) compression strength) O ,c) final flow stress) O d) tensile strength) O ?e) yield strength O
Home Work: Show that the true strain rate in extruding a round billet of radius ro as a function of distance x from the entry of a conical die can be given as: 2V,rž tana where; Vo: ram velocity (ro-xtana)3
16 30. Forging process is suitable for mass production. Select one: True False
When the liquid type changes in the jet extrusion impact experiment, what does this affect the value of (fy) and why?
Calculate (1) die pressure distribution and (2) forging force for plane strain forging (open die forging). Assume yield strength of the material is Y, and yielding criterion is von Mises. ho 2Lo h Forged to 2L xdx L 'x+value Note: Assume Zo Constant Plane strain Die pressure distribution h L L Die pressure distribution h MATERIAL L dx -(-1) Friction Hill Y L When 0; =Y P=Y' = Calculate forging force X L dF elemental volume Average pressure
Manufacturer process A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength = 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking. Take: Ac=0.06
Show that the true strain rate in extruding a round billet of radius r. as a function of distance x from the entry of a conical die can be given as: 2Voržtana έ where; V.: ram velocity (ro-xtana)3
A 3in long and 1in diameter billet is extruded in a direct extrusion operation with an rx = 4.0. The extrusion has a cross section. The angle of the die (half angle) is 90o. The work metal has a resistance coefficient of 60ksi and a strain hardening exponent of 0.18. Use Johnston's formula with a = 0.8 and b = 1.5 to estimate the extrusion stress. Determine the pressure applied to the end of the billet when the piston moves forward.
3XPL@!N THE PROCESS @ND PROVIDE EXAMPLES FORMING OPERATIONS 1. Forging is mechanically working or deforming a single piece of a usually hot metal; this may be accomplished by the application of successive blows or by continuous squeezing. 2. Rolling, the most widely used deformation process, consists of passing a piece of metal between two rolls; a reduction in thickness results from compressive stresses exerted by the rolls. 3. Extrusion, a bar of metal is forced through a die orifice by a compressive force that is applied to a ram; the extruded piece that emerges has the desired shape and a reduced cross-sectional area. 4. Drawing is the pulling of a metal piece through a die having a tapered bore by means of a tensile force that is applied on the exit side.