Water enters a pump through a 250mm diameter pipe at 35 kPa. It leaves the pump at 140 kPa through a 150mm diameter pipe. If the flow rate is 150L/s. Assume suction and discharge side of the pump to be of the same elevation. Find the horsepower delivered to the water by the pump. Select the correct response: 38.43 hp 27.42 hp • 11.92 hp 43.12 hp

Water enters a pump through a 250mm diameter pipe at 35 kPa. It leaves the pump at 140 kPa through a 150mm diameter pipe. If the flow rate is 150L/s. Assume suction and discharge side of the pump to be of the same elevation. Find the horsepower delivered to the water by the pump. Select the correct response: 38.43 hp 27.42 hp • 11.92 hp 43.12 hp

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It is desired to deliver 4 gpm at a head of 670 m in a single pump having specific speed not to exceed 40. If the operating speed is not to exceed 1352 rpm, how many stages are required? Select the correct response: 0 7 O 5 3 6 Contin 2.
1.A pipe of diameter 300 m and length 3000 m is used for the transmission of power by water. The total head at the Inlet of the pipe is 400 m. Find the maximum power available at the outlet of the pipe. Take f=0.005 2. The head of water at the Inlet of a pipe of length 1500 m and diameter 400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to the pipe. Find the velocity of water at the outlet of the nozzle if f=0.01 for the pipe.
A pump draws water from an 8 in. suction pipe and discharges through a 6 in. pipe in which the velocity is 12 fps. The pressure is –5 psi at point 1 in the suction. The 6 in. pipe discharges horizontally into the air. The power delivered to the pump is 30hp whose efficiency is 70. Determine: a. the water horsepower 21 18 15 b. the total dynamic head in feet 94.316 78.564 67.369 c. To what height h in feet above the suction gage can the water be raised? 81.716 65.498 54.303 please answer immediately thankyou
Q.2 A centrifugal pump is required to pump water to an open water tank situated 4 km away from the location of the pump through a pipe f diameter 0.2 m having Darcy's frřiction factor of 0.01. The average speed of waterinthe pipe is 2 m/s. If it is to maintain a constant heac of 5 m in the tank, neglecting other minor losses, the absolute discharge pressure at the pump exit is (a) 0.449 bar (c) 44.911 bar dund (b) 5.503 bar (d) 55.203 bar
A centrifugal pump is used to pump water (1000 kg/m³) to a height of 10m, the water splashes down back into the tank. The diameter of the impeller of the pump is 145 mm, the pump speed is 2900 rpm. The equation to calculate the flow V in the valve depending on the pressure drop differential pressure (dp) in the valve isV = 4 * sqrt (dp), whereas V is in m³/h and dp in bar. Please estimate the water flow.
2. A sump pump turning at 1600 rpm provides a water discharge of 9gpm againts a head of 18ft. Compute the minimum power input. Use the curve below to detremine the efficiency. 1.0 10,000 0.8 1000 300 100 0.6 30 ma 0.4 10 Q = 5 galfmin 0.2 100 300 1000 3000 10.000 30.000
It is desired to deliver 4 gpm at a head of 670 m in a single pump having specific speed not to exceed 40. If the operating speed is not to exceed 1352 rpm, how many stages are required? Select the correct response: 3 4 6. 7 2
Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 95 m below the reservoir surface. The turbine delivers 0.950 MW. Calculate the required flow of water in m3/min if friction is neglected. If friction were included would a higher or lower flow rate be required? (Note: The equation you will solve in this problem has multiple roots. Find a solution less than 1.0 m3/s.) V=___m^3/min?
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
A submersible pump is to be selected for the installation on a newly drilled deep well. The static water level (SWL) of the water inside the well is 8.7m from the natural ground level and the centerline of the discharge pipeline is 3.5 feet above the natural ground level. Based on the test pumping results from the SWL the flow velocity at the pipeline discharge was 8.09 ft/s and the design pressure is 40 psi to assure that the water can reach the elevated water tank. The total head losses are assumed to be 12 feet. a.) Find the total dynamic head (TDH) of the submersible pump needed for sizing in feet ? b.) What will be the suitable pipe diameter for the system riser in inches?
Len is asked to design a small water pump for an aquarium. The pump should deliver 18.0 Lpm of water at a net head of 1.6 m at its best efficiency point. A motor that spins at 1200 rpm is available Suppose the pump is modified by attaching a different motor, for which the rpm is 1800 rpm. If the pumps operate at homologous points (namely, at the BEP) for both cases, predict the volume flow rate and net head of the modified pump. Calculate the pump specific speed of the modified pump, and compare to that of the original pump. Discuss.
A Pelton wheel develops 70 kW under a head of 60 m of water. It rotates 400 rpm. Overall efficiency is 80%. Find the discharge rate in m³/s. Use the equation below, where P is power of the turbine shaft and no is the overall efficiency, where specific weight of water is is 9.80 kN/m³ no P YQH A generator is driven by a small, single-jet Pelton turbine designed to have a power specific speed sp 0.20. The effective head at nozzle inlet is 200 m and the nozzle velocity coefficient is 0.985. The runner rotates at 880 rev/min, The turbine overall efficiency is 80%. Find (a) the power delivered by the shaft of the turbine and (b) find the power delivered by the water to the turbine. where density of water is 1000 kg/m³ and g is 9.80 m/s². Use Stup Ω P/p (gHE)* Overall efficiency ne and Power developed at turbine shaft hydraulic power P YQH