Vocabulary Series: Items are all on one loop connected to the sides of the power source (battery) Parallel: items are on separate loops connected to the sides of the power source (battery) 1. Draw a circuit with a bulb, switch, and single cell, connected with wire. 2. Draw a circuit with 2 bulbs in series with a resistor, a switch, and a 2 cell battery connected with wire. 3. Draw a circuit with a buzzer and a light bulb in parallel with 2 switches and one 2 cell battery connected with wires. 4. Draw a circuit with 10 light bulbs in series with a switch and an AC power source connected with wires. 5. Draw a circuit with a motor, a switch, and two 2-cell batteries in series connected with wires.

Vocabulary Series: Items are all on one loop connected to the sides of the power source (battery) Parallel: items are on separate loops connected to the sides of the power source (battery) 1. Draw a circuit with a bulb, switch, and single cell, connected with wire. 2. Draw a circuit with 2 bulbs in series with a resistor, a switch, and a 2 cell battery connected with wire. 3. Draw a circuit with a buzzer and a light bulb in parallel with 2 switches and one 2 cell battery connected with wires. 4. Draw a circuit with 10 light bulbs in series with a switch and an AC power source connected with wires. 5. Draw a circuit with a motor, a switch, and two 2-cell batteries in series connected with wires.

Physics for Scientists and Engineers

10th Edition

ISBN:9781337553278

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter27: Direct-current Circuits

Section: Chapter Questions

Problem 16P: You have a faculty position at a community college and are teaching a class in automotive...

See similar textbooks

Similar questions

A student in a physics lab mistakenly wired a light bulb, battery, and switch as shown in Figure 21.44. Explain why the bulb is on when the switch is open, and off when the switch is closed. (Do not try this-it is hard on the battery!)
You have a faculty position at a community college and are m (caching a class in automotive technology. You are deep in a discussion of using jumper cables to start a car with a dead battery from a car with a fresh battery. You have drawn the circuit diagram in Figure P27.16 to explain the process. The battery on the left is the live batten- in the correctly functioning car, with emf and internal resistance RL where the L. subscript refers to live. Its terminals are connected directly across those of the dead battery, in the middle of the diagram, with emf and internal resistance RD where the D subscript refers to "dead Then, the starter in the car with the dead battery is activated by closing the ignition switch, allowing the car to start. The resistance of the starter is Rs. A student raises his hand and asks, So is the dead battery being charged while the starter is operating? How do you respond?
If you were 10 design an electric healer using Nichrome wire as the healing element, what parameters of the wire could you vary to meet a specific power output such as 1 000 W?
What would be the maximum cost of a CFL such that the total cost (investment plus operating) would be the same for both CFL and incandescent 60-W bulbs? Assume the cost of the incandescent bulb is 25 cents and that electricity costs 10 cents/kWh, Calculate the cost for 1000 hours, as in the cost effectiveness of CFL example.
Integrated Concepts A light-rail commuter train draws 630 A of 650-V DC electricity when accelerating, (a) What is its power consumption rate in kilowatts? (b) How long does it take to reach 20.0 m/s stalling from rest if its loaded mass is 5.30 1()4 kg, assuming 95.0% efficiency and constant power? (c) Find its average acceleration. (d) Discuss how the acceleration you found for the light-rail train compares to what might be typical for an automobile.
Construct Your Own Problem Consider a battery used to supply energy to a cellular phone. Construct a problem in which you determine the energy that must be supplied by the battery, and then calculate the amount of charge it must be able to move in order to supply this energy. Among the things to be considered are the energy needs and battery voltage. You may need to look ahead to interpret manufacturer’s battery ratings in ampere hours as energy in joules.
A 0.0200- ammeter is placed in series with a 10.00- resistor in a circuit, (a) Draw a circuit diagram of the connection, (b) Calculate the resistance of the combination, (c) If the voltage is kept the same across the combination as it was through the 10.00- resistor alone, what is the percent decrease in current? (d) If the current is kept the same through the combination as it was through the 10.00-resistor alone, what is the percent increase in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
Solve Example 21.5, but use loop abcdefgha instead of loop akledcba. Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
A 120.-V motor has mechanical power output of 2.50 hp. It is 90.0% efficient in converting power that it takes in by electrical transmission into mechanical power. (a) Find the current in the motor. (b) Find the energy delivered to the motor by electrical transmission in 3.00 h of operation. (c) If the electric company charges 0.110/kWh, what does it cost to run the motor for 3.00 h?
The rather simple circuit shown below is known as a voltage divider. The symbol consisting of three horizontal lines is represents “ground” and can be defined as the point where the potential is zero. The voltage divider is widely used in circuits and a single voltage source can be used to provide reduced voltage to a load resistor as shown in the second part of the figure, (a) What is the output voltage Vout of circuit (a) in terms of R1,R2,andVin (b) What is the output voltage Vout of circuit (b) in terms of R1,R2,RLandVin
You have a faculty position at a community college and are teaching a class in automotive technology. You are deep in a discussion of using jumper cables to start a car with a dead battery from a car with a fresh battery. You have drawn the circuit diagram in Figure P27.16 to explain the process. The battery on the left is the live battery in the correctly functioning car, with emf and internal resistance RL, where the L subscript refers to live. Its terminals are connected directly across those of the dead battery, in the middle of the diagram, with emf and internal resistance RD, where the D subscript refers to dead. Then, the starter in the car with the dead battery is activated by closing the ignition switch, allowing the car to start. The resistance of the starter is RS. A student raises his hand and asks, So is the dead battery being charged while the starter is operating? How do you respond? Figure P27.16
What are the advantages and disadvantages of connecting batteries in series? In parallel?